Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 327

background image

Safety instructions

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

64

3.4

Basic safety instructions

WARNING

Before starting work with and on the machine, read and
observe the basic safety instructions!

Secure tractor and machine against accidental starting and
rolling before carrying out any work with and on the machine!

Secure lifted machine parts/the lifted machine against
accidental lowering!

Make sure that people leave the hazardous areas!

Non-observance of these instructions may cause most serious
bodily injury (irreversible) or even death.

WARNING

Risk due to lacking road and operational safety!

Check tractor and machine for their road and operational safety
before each startup!

The machine is only allowed to be operated by one person:

•

mainly from the driver seat of the tractor

Secure machine against accidental operation:

•



Turn the tractor engine off

•



Pull the ignition key out

•

Lock the tractor cabin

Secure the machine against accidental rolling:

•

By means of the parking brake and/or the chocks



WARNING

As a basic principle, the manipulation of actuating and
operating elements is generally prohibited!

Do not block any operating elements on the tractor, which serve to
directly initiate hydraulic or electrical movements of components, e.
g. folding, swivelling and sliding operations. The respective
movement must automatically stop as soon as the respective
operating element is released. This shall not apply to

•

continuous movements or

•

automatically controlled movements or

•

movements which, for functional reasons, require a floating or
pressing position.

«
...
62
63
64
65
66
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: NARGESA Страницы: 33

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: Bahco Страницы: 9

Бренд: NANLUX Страницы: 39

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренд: laguna Страницы: 16

Бренд: Lafayette Страницы: 2

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: TDR Страницы: 8

Бренд: SAC Страницы: 2

Бренд: Sabo Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды