Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 233

Страница: 233 / 327

Service and maintenance of machine

233

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

Every 500 service hours or once a year

•

Check frame and drawbar for cracks.

•

Clean the filter elements of the compressed-air brake system depending on the operating
conditions.

•

Have the hydraulic hose pipes checked for their operational safety by an expert.

•

Check the hydraulic filter for contamination (observe the cleaning indicator!).

•

Read out the fault memory of the electro-hydraulic forced steering axle system SES and have
malfunctions remedied by an authorised workshop.

•

Change the gear lubricant oils.

•

Lubricate the chain tensioner screws of the transport floor.

•

Carry out maintenance work on the cam-type cut-out clutch.

Every 2 years

•

Have the hydraulic oil changed and the return-flow and pressure filter elements replaced by an
authorised workshop.

Before longer downtimes

•

Thoroughly clean the machine.

•

Lubricate and grease the machine (the piston rods of the hydraulic cylinders as well).

•

Touch up paintwork.

Before winter period

•

Lubricate the transport floor chains to prevent them from freezing.

After end of season

•

Remove all cutting knives.

•

Grease or lubricate all movable parts of the cutting unit and the machine.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды