Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 327

background image

Product description

35

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.7.4

Load-sensing hydraulic system

•

Connect the hydraulic system only after it has been
depressurised.

•

Turn the tractor engine off before connecting the hydraulic
system.

•

Always connect the load-sensing control line when connecting
the hydraulic connector "Flow line" to the pressure line leading
to the hydraulic pump of the tractor provided for this purpose.

The electro-hydraulic control block of the machine is directly connected with the hydraulic pump of the
tractor via the load-sensing control line. The current machine demand for hydraulic oil determines the
pressure and the delivery rate of the tractor's hydraulic pump.

Tractor

Machine

Fig. 18

(1)

Electro-hydraulic control block at the machine

(2)

Load-sensing control line

(3)

Adjustable hydraulic pump of tractor

(4)

Hydraulic connector "Return line", connected to the free return port of the tractor provided for
this purpose,

not

via control device

(5)

Hydraulic connector "Flow line", connected to the pressure line leading to the hydraulic pump of
the tractor, oil supply

not

via control device

If the standby pressure in the LS system is too low and cannot be
increased at the tractor, it is possible to retrofit an LS amplifier.

Please contact your dealer.

«
...
33
34
35
36
37
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: ACS Страницы: 56

Бренд: Laica Страницы: 4

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: Palazzetti Страницы: 112

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Magma Страницы: 16

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Baileigh Industrial Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды