Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 196

Страница: 196 / 327

Operation

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

196

6.2.3.39 Display information of machine set-up menu

In the machine set-up menu, automatic functions and features can
be activated/deactivated.

(1)



Opening time of tailgate after reaching the
first opening width (only forage wagon with
dosing unit)

(2)



Reversing time of transport floor with full
wagon (only forage wagon with dosing
unit)

(3)



Automatic charging system
activated/deactivated, here activated

(4)



Crossover conveyor mounted / not
mounted, here not mounted

(5)



Beep upon response of knife protection
system activated/deactivated, here
activated

(6)



Connection of silage additive pump in
charge mode activated/deactivated, here
activated

(7)



Automatic locking of steering axle during reverse travel activated/deactivated, here activated

(8)



Automatic locking of steering axle in discharge mode activated/deactivated, here activated

(9)



Automatic locking of steering axle in road travel mode activated/deactivated, here deactivated

(10)



Automatic setting of folding drawbar position in discharge mode activated/deactivated, here
activated

(11)



Automatic setting of folding drawbar position in charge mode activated/deactivated, here
deactivated

(12)



Automatic setting of folding drawbar position in road travel mode activated/deactivated, here
deactivated

(13)



Automatic knife system

(14)



External operation

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды