Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 327

background image

Commissioning

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

116

5.12.3.1 Connect dual-line service brake system

1.

Open the caps of the hose couplings on the tractor.

2.

Remove the hose coupling of the brake line (yellow) from the blank connection.

3.

Clean soiled sealing rings or replace damaged sealing rings.

4.

Properly fix the hose coupling of the brake line (yellow) to the yellow marked coupling device at
the tractor.

5.

Remove the hose coupling of the feed line (red) from the blank connection.

6.

Clean soiled sealing rings or replace damaged sealing rings.

7.

Properly fix the hose coupling of the feed line (red) to the red marked coupling device at the
tractor.



When connecting the feed line (red), the system pressure coming from the tractor automatically
pushes the push button for the release valve on the trailer brake valve out.

8.

Release the parking brake and/or remove the chocks.

5.12.3.2 Connect hydraulic brake system

Only couple clean hydraulic clutches.

•

Clean hydraulic plug and hydraulic sleeve if necessary.

•

Slip the hydraulic plug into the hydraulic sleeve until the
hydraulic plug noticeably locks.

•

Check the coupling spot of the hydraulic brake line for correct
and tight seat.

•

The connected hydraulic brake line:



must easily give way to any movements during cornering
without any stress, buckling or chafing,



must not chafe against external components.

•

Check the hydraulic brake system for proper functioning before
carrying out transport journeys.

1.



Remove the hydraulic sleeve (1) from the
machine's blanked-off connecting piece
(2).

2.



Couple the machine's hydraulic sleeve to
the tractor's hydraulic plug of the hydraulic
brake system.

3.



Release the parking brake of the machine.

Fig. 61

«
...
114
115
116
117
118
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Laica Страницы: 4

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: 3M Страницы: 2

Бренд: GE Страницы: 698

Бренд: SAMCHULLY Страницы: 48

Бренд: Gallagher Страницы: 6

Бренд: National Instruments Страницы: 10

Бренд: Garden Treasures Страницы: 2

Бренд: Yamaha Страницы: 48

Cutler-Hammer ATC-300

Бренд: Eaton Страницы: 32

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Milestone Страницы: 64

Бренд: Jenx Страницы: 34

Бренд: B+S Страницы: 16

Бренд: TECshow Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды