manualshive.com logo in svg

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации, Страница: 135 / 327

Поделиться
Скачать
Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 135

 

Operation

 

 

135 

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO   03.18 

 

(1)

Screen. Depending on the selected 
function, the following menu appears: 

• 

Working

 menu. The 

Working

 menu 

displays the selected functions and 
the operating states during charging 
and discharging. 

• 

Road Travel

 menu. The 

Road 

Travel

 menu appears with the road 

travel mode activated. 

• 

SET 

menu. The 

SET

 menu displays: 



the software version, 



machine parameters. 

(2) 

Switch control system on (I)/off (0) 

(3) 

Switch road travel mode on/off/ Scroll 
through menu 

(4)

Switch crossover conveyor off 

(5)

Switch crossover conveyor on and change 
driving direction 

(6)

Switch 

Discharge Mode A II

 on/off 

(7)

Switch 

Discharge Mode A I

 on 

(8)

Switch automatic charging system on/off 

(9)

Reverse transport floor/Reduce feed rate 
of transport floor during discharge (in 
combination with key 11) 

(10)

Double feed rate of transport floor for 
complete emptying (transport floor level 
II)/Increase feed rate of transport floor 
during discharge (in combination with key 
11) 

 

 

Fig. 82 

 

(11)

Switch transport floor on/Set feed rate of transport floor (in combination with keys 9 and 10) 

(12)

Select 

SET

 menu/Call up service hours and transported loads counter 

(13)

Switch lighting in cargo space on/off/ Return to Working menu 

(14)

Lower tailgate 

(15)

Lift tailgate 

(16)

Lift folding drawbar 

(17)

Lower folding drawbar 

(18)

Retract cutting unit 

(19)

Extend cutting unit 

(20)

Lock steering axle 

(21)

Unlock steering axle 

(22)

Lift pick-up 

(23)

Lower pick-up to floating position/ no floating (rigid) 

 

 

 

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов