Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 124

Страница: 124 / 327

Commissioning

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

124

5.13.3.3 Disconnect hydraulic brake system with emergency brake valve



Use the parking brake to secure tractor and machine against accidental rolling.



Make sure that the hydraulic pipe between tractor and machine has been depressurised.



Set the brake control valve at the tractor such that the hydraulic oil can flow back to the
tractor.



Press the drain valve (7) at the emergency brake valve (3).



The hydraulic oil flows back to the tractor and the pressure accumulator (4) is depressurised.



Remove the ripcord (1) from the tractor.



Uncouple the hydraulic sleeve (2).



Slip the hydraulic sleeve onto the machine's blanked-off connecting piece.

(1)



Ripcord

(2)



Coupling box

(3)



Emergency brake valve

(4)



Pressure accumulator

(5)



Brake cylinder

(6)



Brake drum

(7)



Drain valve

Fig. 67

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды