Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 28

Страница: 28 / 327

Product description

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.5.5

Braking axle

(1)

Diaphragm brake cylinder

(2)

Slack adjuster for brake camshaft

(3)

Brake camshaft

(4)

Connecting rods for parking brake

(5)

Test connection for pressure gauge

Fig. 11

2.6

Steering axle

2.6.1

Passive steering axle

The unlocked passive steering axle

•

can move freely and follows the turning
radius of the corner during cornering.

•

protects the sward during cornering.

•

reduces tyre wear during cornering on
paved areas.

The passive steering axle is locked and unlocked
via the control set of the tractor.

Fig. 12

2.6.2

Detection of travel direction with passive steering axle

Optional extra in conjunction with ISOBUS control1

With the help of the ABS sensor in the steering axle, the ISOBUS control system detects the direction
of travel and automatically locks / unlocks the passive steering axle.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации, Страница: 28 / 327

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы: