Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 69

Страница: 69 / 327

Safety instructions

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18



within the operating/hazardous area of the machine,



beneath lifted and unsecured movable machine parts,



on the transport floor as long as the tractor engine is running.

•

Avoid sudden changes of direction when travelling uphill and downhill and when traversing hills
(risk of tipping over!).

•

Only actuate powered machine parts if people keep sufficient safe distance to the machine!

•

Safely support folded-up covers before standing underneath them!

•

Immediately switch the tractor's p.t.o. shaft off in case of a response of the overload clutch.

•

Secure the tractor against accidental starting and rolling before leaving it!

For this purpose,



apply the parking brake,



turn the tractor engine off,



pull the ignition key out.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды