Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 46

Страница: 46 / 327

Product description

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.18

Type plate

(1)

Type plate with CE symbol

(2)

Vehicle/Machine ID number (embossed
into the frame)

(3)

Settings for ALB regulator

Fig. 33

Information on the type plate:

(1)



Manufacturer

(2)



CE symbol

(3)



Vehicle/Machine ID number

(4)



Type

(5)



Empty weight [kg]

(6)



Gross vehicle weight rating [kg]

(7)



Admissible tongue load/front axle load [kg]

(8)



Admissible rear axle load [kg]

(9)



Approval number

(10)



Year of manufacture

(11)



Rated speed [min-1]

(12)



Admissible hydraulic pressure [bar]

(13)



Maximum admissible speed [km/h]

Fig. 34

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации, Страница: 46 / 327

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы: