Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 255

Страница: 255 / 327

Service and maintenance of machine

255

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

8.10.3.1 Remove cutting knives



Retract the cutting unit via the control set.



Fold the folding drawbar by means of the
hydraulic cylinders to increase the free
space to the cutting knives.



Switch the oil circulation between tractor
and machine off.



Secure tractor and machine against
accidental starting and rolling.



Pull the bolt (1) out.



Fold the cover plate (2) down.

Fig. 115



Wear protective goggles.



Wear protective gloves.



Remove the knife lever (3) and the
mounting lever (4) out of the holder (5).

Fig. 116

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды