Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 86

Страница: 86 / 327

Safety instructions

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

87010285

Close the stop-cock (position 0) to secure the tailgate before carrying out work
beneath the lifted tailgate.

54106501

Adjust travelling height of hydraulic chassis via three-way cock:

(1)

Upper stop-cock to the right (open) = Right-hand vehicle side
preselected

Lower stop-cock down (open) = Right-hand vehicle side can be
lifted (max. 2 cm)

(2)

Upper stop-cock down (closed) and lower stop-cock to the right
(closed) = Travelling height cannot be changed

(3)

Upper stop-cock to the left (open) = Left-hand vehicle side
preselected

Lower stop-cock down (open) = Left-hand vehicle side can be
lifted (max. 2 cm)

(1)

(2)

(3)

87010288

This pictograph marks fixing points for lifting equipment (jack).

87006091

This pictograph marks lashing points for fixing lashing equipment when
transporting the machine.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды