manualshive.com logo in svg

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации, Страница: 164 / 327

Поделиться
Скачать
Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 164

Operation

 

 

 

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO   03.18 

164 

 

 

6.2.1 

Design of ISOBUS control 

 

 

The ISOBUS control complies with the latest ISO standard. 

If your tractor's software and hardware comply with the latest ISO 
standard, you will not require our control set. You will then be able to 
directly operate the machine via your tractor control set. 

 

 

The ISOBUS control set is automatically switched on and off when 
the tractor ignition is turned on and off. In case of longer downtimes 
of the machine, additionally disconnect the mobile tractor connecting 
cable. 

 

 

Fig. 84 

 

The ISOBUS control mainly consists of: 

• 

the control set (1), 

• 

the control unit (2), 

• 

the sensors (3) to determine operating states, e. g. Steering Axle Locked or Steering Axle 
Unlocked, 

• 

the connecting cable (4) for the silage additive pump (5) (optional extra). 

The control set (1) is mounted on the tractor and is connected to the control unit (2) of the machine via 
the connecting cable (6). 

All functions required for operating the machine as well as for transport journeys are actuated via the 
keys (7) of the control set. The symbols on the keys identify the executable functions. 

After a key has been pressed, the control unit triggers the corresponding solenoid valve at the electro-
hydraulic control block (8) to carry out the selected function. Individual sensors (3) determine the 
respective operating state of the selected assembly, e. g. Steering Axle Locked or Steering Axle 
Unlocked. The operating states are graphically shown on the screen (9). 

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов