manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 78 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 78

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 23

(2) Remaining paper detection

a. Remaining paper detection 

Remaining paper detection is performed according to four stages, i.e.
three stages with paper and one stage with no paper, and the result is
displayed.

b. Detection method

The number of remaining sheets is determined according to the num-
ber of times the remaining paper sensor changes from the time the
paper feed tray starts lifting up to the time when the upper detection
sensor comes ON.

(Figure showing state transition of the remaining paper detection sensor during tray elevation and 

changes in status according to the number of remaining sheets)

The no-paper detection sensor 
detects the state of no remaining paper. 

1/3 Field
Sensor logic: Low

2/3 Field
Sensor logic: Hi

3/3 Field
Sensor logic: Low

During no-paper detection

Remaining paper 1/3 position

Remaining paper 2/3 position

Remaining paper 1/3 position

Turn plate

MCPED
(paper sensor)

Remaining Paper 
Detection Actuator

MCSPD 
(remaining paper detection sensor)

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов