manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 284 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 284

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 26

Operation/Procedure

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The load selected in procedure 1 operates.

Press [CUSTOM SETTINGS] key to stop the operation.

*

All fans: All the fans controlled by the engine.

Operation/Procedure

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The transfer belt performs contact/separation with the OPC drum.

Press [CUSTOM SETTINGS] key to stop the operation.

NOTE: Before disassembling the transfer unit, use this simulation to

separate the transfer unit from the OPC drum.

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 
repeating the operation several times.

6-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of each fan motor and its 
control circuit.

Section

Other

Item

Operation

1

VFM-EX

Exhaust fan motor (VFM-EX1, 2, 3, VFM-BKL, 
VFM-BKU)

2

CFM-UP 

Heat exhaust fan motor (Paper exit upper) 
(CFM-U1, 2, 3, VFM-BKR)

3

CFM-R 

Cooling fan motor (Right side) (CFM-R1, 2, 3)

4

CFM-DC

Cooling fan motor (Power source) (CFM-DC1, 
2)

5

CFM-DV

Cooling fan motor (Developing) (CFM-DV)

6

CFM-ICU /HDD

Cooling fan motor (Controller/HDD) (CFM-
ICU/HDD)

7

ALL

All fans control*

8

CFM-AD

Cooling fan motor (paper exit center) (CFM-
U4)

(Exhaust fan motor, heat exhaust fan motor (paper exit upper),
cooling fan motor (right side) cooling fan motor (power source),
cooling fan motor (developing), cooling fan motor (paper exit cen-
ter))

SIMULATION 6-1

FEED OUTPUT CHECK. SELECT 1- 33, AND PRESS START.

1.MSWPR  2.HLPR  3.DCPR  4.MM   5.DM

6.DVM    7.TURM  8.TRM   9.POM1

10.POM2_FW   11.POM2_RV   12.VPM

13.RRC    14.PSBC   15.PSPS   16.T1PFC

17.T2PFC  18.HPFC   19.T1PUS  20.T2PUS

21.HPLS   22.T1LUM  23.T2LUM  24.DSKPFC1

25.DSKPFC2  26.M1PFC  27.M2PFC  28.M1PUS

29.M2PUS    30.M1LUM  31.M2LUM  32.TRC_LCC

33.FUM      34.MPFPUS 35.MPFC   36.MPFGS

    2

SIMULATION 6-1

FEED OUTPUT CHECK. EXECUTING···.

1.MSWPR  2.HLPR  3.DCPR  4.MM   5.DM

6.DVM    7.TURM  8.TRM   9.POM1

10.POM2_FW  11.POM2_RV  12.VPM

13.RRC    14.PSBC   15.PSPS   16.T1PFC

17.T2PFC  18.HFC    19.T1PUS  20.T2PUS

21.HPLS   22.T1LUM  23.T2LUM  24.DSKPFC1

25.DSKPFC2  26.M1PFC  27.M2PFC  28.M1PUS

29.M2PUS    30.M1LUM  31.M2LUM  32.TRC_LCC

33.FUM      34.MPFPUS 35.MPFC   36.MPFGS

    2

1

1

1

1

1

1

1

1

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.

6-3

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the transfer unit and 
the related circuit. 

Section

Process (Transfer)

Item

1

TURM (RELEASE)

Transfer unit separation state

2

TURM (JOINT)

Transfer unit contact state

Press [START] key, and the operation is 
started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 
repeating the operation several times.

After completion 

Press [CUSTOM SETTINGS] key to stop the 
operation.

SIMULATION 6-2

FAN MOTOR CHECK. SELECT 1-8, CAND PRESS START.
1. VFM-EX   2. CFM-UP 
3. CFM-R    4. CFM-DC
5. CFM-DV   6. CFM-ICU /HDD
7. ALL      8. CFM-AD 

    2

SIMULATION 6-2

FAN MOTOR CHECK..
2. CFM-UP 

  2

SIMULATION 6-3

TURM CHECK. SELECT 1-2 CAND PRESS START.
1. TURM(RELEASE)
2. TURM(JOINT)

    2

SIMULATION 6-3

TURM CHECK. EXECUTING...
1. TURM(RELEASE)

  2

SIMULATION 6-3

TURM CHECK.

COMPLETE....

1. TURM(RELEASE

  2

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов