Sharp AR-M550N Скачать руководство пользователя страница 221

Страница: 221 / 460

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 6

4) Go through the modes specified in Simulation 8-18.

5) Select the number that corresponds to the adjustment item (CRHV

PLUS / CRHV MINUS) using the numeric keypad.

6) Press the Start key

7) Press the Start key to have the voltage output for 30 seconds.

The operation can be stopped with the CUSTOM SETTINGS key.

If the output voltage is not within the requirement, do the following
steps.

8) Enter the adjustment value using the numeric keypad.

9) Press the Start key.

(The adjustment value is put into memory, and the corresponding
voltage is output for 30 seconds.)

Repeat steps 8 to 9 until the output requirement is satisfied.

This adjustment is needed in the following situations:

• The developing unit has been disassembled.

• The print density is low.

• The toner is excessively dispersed.

1) Remove the developing unit of the machine.

2) Remove the developing unit cover and blade cover.

3) Loosen the DV doctor fixing screws.

4) Manually turn the DV roller to align the marking on the DV roller

surface with the DV doctor position.

5) Insert a 0.525mm clearance gauge in between the DV roller and

DV doctor so that the gauge is positioned at a distance of 40 mm to
70 mm from the DV doctor end face.

6) Tighten the DV doctor fixing screws while pressing the DV doctor

in the arrow direction.
(This should be done for both front and rear frames.)

Press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

ADJ 2

Adjusting the developing unit

ADJ 2A

Adjust the developing doctor gap

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. SELECT 1-2, AND

PRESS START.

1.CRHV PLUS

200

2.CRHV MINUS

200

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. INPUT VALUE, AND

PRESS START.

1.CRHV PLUS (0-250)

200

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. EXECUTING···.

1.CRHV PLUS(0-250)

200

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 221 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: