Sharp AR-M550N Скачать руководство пользователя страница 247

Страница: 247 / 460

: Feb. 9 2004

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 32

(SIM 46-10) (Text/photo mode)

(SIM 46-11) (Photo mode)

3) Using the numeric keypad, select the number that corresponds to

the copy density adjustment level. (Choose from numbers 3 to 11.)

4) Press the Start key

5) Press the Start key (A copy is created.)

If the copied image density is not at an acceptable level, do the fol-
lowing steps.

6) Adjust the copy density by entering an appropriate value through

the numeric keypad.

A larger value provides higher density.

7) Press the P or Start key.

This applies the adjustment value.

Pressing the Start key starts copy operation as well as applying the
adjustment value.

8) Check the copied image density.

Repeat steps 5 to 9 until an acceptable copied image density is
obtained.

1) Set the original on the original table.

2) Go through the modes specified in Simulation 46-18.

Item

Set

range

Default

TRAY SELECT

Paper feed tray selection

COPY START

Copy START (Default)

EXP LEVEL

Exposure level selection

1.0

Exposure level 1.0

0 - 99

1.5

Exposure level 1.5

2.0

Exposure level 2.0

2.5

Exposure level 2.5

3.0

Exposure level 3.0

3.5

Exposure level 3.5

4.0

Exposure level 4.0

4.5

Exposure level 4.5

5.0

Exposure level 5.0

Item

Set

range

Default

TRAY SELECT

Paper feed tray selection

COPY START

Copy START (Default)

EXP LEVEL

Exposure level selection

1.0

Exposure level 1.0

0 - 99

1.5

Exposure level 1.5

2.0

Exposure level 2.0

2.5

Exposure level 2.5

3.0

Exposure level 3.0

3.5

Exposure level 3.5

4.0

Exposure level 4.0

4.5

Exposure level 4.5

5.0

Exposure level 5.0

ADJ 9E

Adjust the copied image gamma in copy
mode

Select 2, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

Item

Set

range

Default

TRAY SELECT

Paper feed tray selection

PRINT START

Print start (Default)

EXP LEVEL

Exposure level selection

OC_AE

AE mode (OC)

0 - 127

OC_CHARA

Text mode (OC)

OC_MIX

Text/Photo mode (OC)

OC_PHOTO

Photo mode (OC)

SPF_AE

AE mode (SPF)

SPF_CHARA

Text mode (SPF)

SPF_MIX

Text/Photo mode (SPF)

SPF_PHOTO

Photo mode (SPF)

CIS_AE

AE mode (CIS)

CIS_CHARA

Text mode (CIS)

CIS_MIX

Text/Photo mode (CIS)

CIS_PHOTO

Photo mode (CIS)

SIMULATION 46-18

GAMMA SETUP(COPIER). SELECT 1-14, AND PRESS START.

0.TRAY SELECT

1.PRINT START 2.EXP LEVEL

3.OC_AE

4.OC_CHARA 5.OC_MIX

6.OC_PHOTO

7.SPF_AE

8.SPF_CHARA

9.SPF_MIX

10.SPF_PHOTO

11.CIS_AE

12.CIS_CHARA

13.CIS_MIX

14.CIS_PHOTO

SIMULATION 46-18

GAMMA SETUP. INPUT VALUE 0-127, AND PRESS START.

3.OC_AE

SIMULATION 46-18

GAMMA SETUP. NOW PRINTING.

SIMULATION 46-18

GAMMA SETUP. SELECT 1-6, AND PRESS START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

Select other than 0 - 2,
and press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

Select 1,
and press
[START] key.

Select 0, and press [START] key.

SIMULATION 46-18

EXP.LEVEL SETUP FAX(SUPER FINE). SELECT 3-14, AND PRESS

START.

(EXP.LEVEL SELECT)

3.AUTO 4.1.0 5.2.0

6.3.0 7.4.0 8.5.0

9.AUTO(H) 10.1.0(H) 11.2.0(H)

12.3.0(H) 13.4.0(H) 14.5.0(H)

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 247 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: