manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 288 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 288

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 30

Operation/Procedure

1) Select the number corresponding to the target of the operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1) is operated.

Press [CUSTOM SETTINGS] key to stop the operation.

Operation/Procedure

The operating conditions of the sensors and detectors are displayed. 

The active sensors and detectors are highlighted.

Operation/Procedure

1) Select the number corresponding to the target of the operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1) is operated for 10sec.

Press [CUSTOM SETTINGS] key to stop the operation.

NOTE: Do not execute this simulation with toner in the toner bottle and

the intermediate toner tank. Excessive toner may enter the
developing section, causing overtoner. Check that there is no
toner in the toner bottle and the intermediate toner tank or dis-
assemble the toner motor before executing this simulation.

Operation/Procedure

1) Press [START] key.

The toner motor rotates 2 turns, and the toner presence/empty in
the toner hopper is displayed. 

Toner empty: Normal display

Toner remained:  Highlighted display

9

9-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check and adjust the operation of the load 
(clutch/solenoid) in the duplex section and the control 
circuit.

Section

Duplex

Item

Operation

1

ADUM1

ADU motor 1: Upstream

2

ADUM2

ADU motor 2: Downstream

3

DGS

ADU gate solenoid

Press [START] key.

Press [CUSTOM SETTINGS] key to stop 
the operations.

9-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the sensors and 
detectors in the duplex section and its control circuit.

Section

Duplex

Item

Operation

DSW_ADU

ADU cabinet open/close detection

AINPD

ADU paper entry detection

APPD1

ADU transport detection 1

APPD2

ADU transport detection 2

SIMULATION 9-1

ADU OUTPUT CHECK. SELECT 1-3, AND PRESS START.

1. ADUM1

2. ADUM2

3. DGS

1

SIMULATION 9-1

ADU OUTPUT CHECK. EXECUTING···.

1. ADUM1

2. ADUM2

3. DGS

1

SIMULATION 9-2

ADU SENSOR CHECK.

DSW_ADU  

AINPD

  APPD1  APPD2

10

10-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the toner motor and 
the related circuit.

Section

Process (Developing)

Item

Operation

TM1

Toner motor 1

TM2

Toner motor 2

Press [START] key.

Press [CUSTOM SETTINGS] key to stop 
the operations. Or after 10sec.

10-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the toner remaining 
quantity sensor and the related circuit.

Section

Process (Developing)

Item

Operation

Press [START] key.

Press [CUSTOM SETTINGS] key to stop the 
operation immediately, or after ** 

SIMULATION 10-1

TONER MOTOR ACTIVATION. SELECT 1-2, AND PRESS START

1. TM1

2. TM2

1

SIMULATION 10-1

TONER MOTOR ACTIVATION. EXECUTING···.

1. TM1

2. TM2

1

SIMULATION 10-2

TONER REST SENSOR CHECK. PRESS START.

TFSD

SIMUL ATION 10-2

TONER REST SENSOR CHECK. EXECUTING···.

TFSD

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов