Sharp AR-M550N Скачать руководство пользователя страница 330

Страница: 330 / 460

AR-M550/M620/M700 SIMULATION 8 - 72

Operation/Procedure

(Print image off-center position adjustment)

NOTE: This simulation cannot provide an accurate adjustment. Do not

use.

1) Enter the number corresponding to the number of the paper feed

tray to be adjusted with 10-key. (Select one of 3 - 9.)

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [P] key or [START] key. When [START] key is pressed, the

adjustment value set and copying is performed.

(Image off-center adjustment)

1) Enter 1 with 10-key.

2) Press [START] key. The adjustment pattern is printed.

3) Check the off-center of the printed image.

(UNIT: 0.1mm/step When the adjustment value is increased, the
print image is shifted to the front direction.)

NOTE: This adjustment can be performed with SIM 50-5.

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key.

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. (Select one of 1 - 6)

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.

∗

To set the copy magnification ratio, perform the following procedure.

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.

Operation/Procedure

(Select the scan mode to be adjusted.)

1) Enter the number corresponding to the scan mode to be adjusted

with 10-key. (Select one of 3 - 5.)

2) Press [START] key.

50-10

Purpose

Adjustment

Function
(Purpose)

Used to adjust the print image off-center position.
(Adjusted separately for each paper feed section.)

Section

Item

Picture quality

Image position

Item

Set range Default

0 TRAY SELECT

Paper feed tray selection

1 - 6

–

1 COPY START

Copy START (Default)

–

2 MAGNIFICATION Print magnification ratio

25 - 400%

100

(Off-center adjustment value)

3 TRAY1

Tray 1 adjustment

0 - 99

4 TRAY2

Tray 2 adjustment

5 TRAY3

Tray 3 adjustment

6 TRAY4

Tray 4 adjustment

7 BPT

Manual feed tray
adjustment

8 LCC

Side LCC adjustment

9 ADU

Adjustment when paper is
fed again from ADU

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

TRAY1

TRAY2

TRAY3

TRAY4

BPT

Manual feed

LCC

Side LCC

Set range

25 - 400 (%)

Select 0, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

50-12

Purpose

Adjustment

Function
(Purpose)

Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)

Section

Item

Picture quality

Image position

Item

Set range

Default

0 TRAY SELECT

Paper feed tray
selection

1 - 5

–

1 COPY START

Copy START (Default)

–

2 MAGNIFICATION Print magnification ratio

25 - 400%

100

(Resist adjustment value)

3 PLATEN

OC mode adjustment

0 - 99

4 SPF SIDE1

SPF front surface
adjustment

5 SPF SIDE2

SPF back surface
adjustment

Select 1,
and press
[START] key.

Select other than 0 - 2, and
press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS

START.

0.TRAY SELECT

1.COPY START

2.MAGNIFICATION

100

(ADJUSTMENT DATA)

3.TRAY1

4.TRAY2

5.TRAY3

6.TRAY4

7.BPT

8.LCC

9. ADU

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND

PRESS START.

2.TRAY1

SIMULATION 50-10

PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS

START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

(ABOVE+10: DUPLEX MODE)

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 330 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: