Sharp AR-M550N Скачать руководство пользователя страница 178

Страница: 178 / 460

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 123

4) Remove the separation roller. (Refer to "b-1. Separation roller" in

this section.)

5) Remove the paper feed paper guide lower unit in the arrow direc-

tion.

6) Remove the bearing metal fixture, and remove the torque limiter.

7) Remove the electromagnetic clutch. (See “b-3. SPF resist roller

brake clutch” in this section)

8) Remove the plastic E-ring to remove the bearing.

9) Slide the No. 1 resist roller drive in the arrow direction, and remove

the plastic E-ring.

10) Remove the No. 1 resist roller drive in the arrow direction.

b-7. SPF paper transport roller 2 brake clutch

b-8. SPF paper transport roller 2 clutch

1) Remove the rear cover. (See “a-1. Cabinet” in the previous sec-

tion, “[External outfit section]”)

2) Disconnect the connector, and remove the plastic E-ring, the SPF

paper transport roller 2 brake clutch (A), and the SPF paper trans-
port roller 2 clutch (B).

b-9. Transport roller 2 (Drive)

b-10. Transport roller 1 (Drive)

1) Remove the cabinet. (See “a-1. Cabinet” in the previous section,

“[External outfit section]”)

2) Remove the document feed tray unit. (See “a. Paper feed unit” in

this section)

3) Remove the No. 1 resist roller idle and the paper feed paper guide

lower unit. (See “b-5. No. 1 resist roller (Drive)” in this section)

4) Remove the plastic E-ring on the cover side to remove the link

lever.

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 178 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: