Sharp AR-M550N Скачать руководство пользователя страница 381 | Manualshive

Страница: 381 / 460

Sharp AR-M550N Скачать руководство пользователя страница 381

AR-M550/M620/M700 SELF DIAG MESSAGE AND TROUBLESHOOTING 9 - 26

Main
code

Sub

code

Title

Machine tray 4 lift-up trouble

F3

42

Phenomenon

Display

Lamp
Message

Details

Machine tray 4 lift-up
trouble
MCPED does not turn on
within the specified time.
MCLUD does not turn on
within the specified time.
The trouble occurs 3
times continuously that
the upper limit sensor
does not turn on by lift-up
operation for 10sec when
inserting a tray or for 2sec
when printing.
For the first and the
second times, guide the
user to pull out the tray in
case of a tray size error.

Section

Engine

Operation
mode

Note

Case 1

Trouble
position/
Cause

MCPED, MCLUD trouble
No. 4 tray lift-up motor
trouble
Improper connection of
the harness of the PCU
PWB, the lift-up unit, and
the paper feed unit

Remedy

Check the harness and
the connector of MCPED
and MCLUD.
Lift-up trouble unit check

Note

Main
code

Sub

code

Title

38V voltage trouble

F4

38

Phenomenon

Display

Lamp
Message

Details

38V voltage falls or rises.

Section

Engine

Operation
mode
Note

Case 1

Trouble
position/
Cause

Improper connection or
disconnection of the
connector and the
harness

Remedy

Check the connector and
the harness of the power
line.

Note

Case 2

Trouble
position/
Cause

PCU PWB trouble
Power unit trouble

Remedy

Check 38V power source
in the power unit and the
PCU PWB.

Note

Main
code

Sub

code

Title

MFP control-FAX communication
trouble (MFP control detection)

F6

00

Phenomenon

Display

Lamp
Message

Details

MFP control-FAX
communication trouble
(MFP control detection)
The booting sequence by
the command line
(9600bps, serial) is not
completed normally.
Communication
establishment error/
framing/ parity/ protocol
error

Section

FAX

Operation
mode

Note

Case 1

Trouble
position/
Cause

Defective connection of
the slave unit PWB
connector
Defective harness
between the slave unit
PWB and the MFP
control PWB
Slave unit PWB mother
board connector pin
breakage

Remedy

Use SIM 25-2 to perform
the automatic developing
adjustment.
Check connection of the
connector between the
slave unit PWB and the
MFP control PWB and
the harness.

Note

Check grounding of the
machine.

Case 2

Trouble
position/
Cause

Slave unit ROM trouble/
no ROM/ Reversed
insertion of ROM/ ROM
pin breakage

Remedy

Check the ROM on the
slave unit PWB.

Note

«
...
379
380
381
382
383
...
»

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов