manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 307 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 307

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 49

Operation/Procedure

Press [START] key, and the adjustment is automatically performed.
When the adjustment is completed, the adjustment result is displayed.
If the adjustment is not completed normally, "ERROR" is displayed.
When an error occurs, the adjustment result is not revised.

Operation/Procedure

1) Enter the target density level in the image density correction with

10-key.

2) Press [START] key.

Operation/Procedure

1) Select the number corresponding to the setting mode with 10-key.

2) Press [START] key.

3) Enter the set value.

4) Press [START] key.

Operation/Procedure

44-2

Purpose

Adjustment

Function
(Purpose)

Used to perform the gain adjustment (image density 
sensor LED current adjustment) of the image density 
sensor and the gain adjustment (OPC drum marking 
sensor LED current adjustment) of the OPC drum 
marking sensor. 

Section

Image process (Photoconductor)

Item

Operation

DMLED

Drum marking sensor gain adjustment

PCLED

Image density sensor gain adjustment value

DRUM

Kind of the drum
0 = Other
1 = SHARP drum 

The gain adjustment is completed.

Press [CUSTOM SETTINGS] key.

44-4

Purpose

Setting

Function
(Purpose)

Used to set the target density level in the image 
density correction.

Section

Image process (Photoconductor/Developing)

Item

Operation

Press [START] key.

Press [CUSTOM SETTINGS] key.

SIMULATION 44-2

PROCON GAIN ADJUSTMENT. PRESS START.
DMLED: 

0

PCLED: 

0

DRUM : 

0

SIMULATION 44-2

PROCON GAIN ADJUSTMENT. EXECUTING...
DMLED

0

PCLED

0

DRUM 

1

Press [START] key.

SIMULATION 44-2

PROCON GAIN ADJUSTMENT. COMPLETE.
DMLED:

0

PCLED: 

0

DRUM :

1

SIMULATION 44-4

1

PROCON INITIAL DENSITY SETUP. PRESS START.
1.PROCON INI DENSITY 

32

SIMULATION 44-4

PROCON INITIAL DENSITY SETUP. INPUT VALUE 0-255, AND
PRESS START.
1.PROCON INI DENSITY

32

44-5

Purpose

Setting

Function
(Purpose)

Used to set the reference developing bias voltage, the 
reference main charger grid voltage, and the laser 
power in the image density correction.

Section

Image process (Photoconductor/Developing)

Item

Operation

Item

Default

1

GRID BIAS VOL

Main charger voltage for 
developing bias voltage correction

350

2

DEVE BIAS VOL

Reference developing bias voltage 
for developing bias voltage 
correction

150

3

LASER POWER

Reference laser power for 
developing bias voltage correction

50

Press [START] key.

Press [CUSTOM SETTINGS] key.

44-9

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to check the data related to the image forming 
section correction (process correction) result 
(corrected main charger grid voltage, the developing 
bias voltage, and the laser power voltage in each print 
mode). (This simulation allows to check that correction 
is performed normally or not.)

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Data

Operation data (Machine condition)

Item

NOTE

DRUM 
ROTATION TIME

OPC drum rotation time (sec)

Reset by SIM 
24-11.

DEVE MIXING 
TIME

Developing roller rotation time 
(sec)

Reset by SIM 
24-11.

DRUM

OPC drum identification code

1: For AR620/
550/625/555
0: For other 
than AR620/
550/625/555

GR BS

Actual main charger grid 
voltage (including correction) / 
Main charger grid voltage 
adjusted with SIM 8-2

DV BS

Actual developing bias voltage 
(including correction) / 
Developing bias voltage 
adjusted with SIM 8-1

1

1

SIMULATION 44-5

1

PROCESS CONTROL TEST. SELECT 1-6, AND PRESS START.
1.GRID BIAS VOL 

350

2.DEVE BIAS VOL 

150

3.LASER POWER    

50

SIMULATION 44-5

PROCESS CONTROL TEST. INPUT VALUE 0-, AND PRESS START.
1.GRID BIAS VOL

350

1

1

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов