manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 304 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 304

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 46

Operation/Procedure

1) Select the number corresponding to the set item with 10-key.

2) Press [START] key.

3) Enter the set value with 10-key.

4) Press [START] key.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The paper width detection level is also displayed.

Operation/Procedure

1) Open the paper feed tray 2 paper feed guide to the max. width

position.

2) Select MAX POSITION with 10-key.

3) Press [START] key.

The max. width detection level is recognized.

4) Press [CUSTOM SETTINGS] key.

5) Open the paper feed tray 3 paper feed guide to the min. width posi-

tion.

6) Select MIN POSITION with 10-key.

7) Press [START] key.

The min. width detection level is recognized.

If the above procedures are not completed normally, "ERROR" is dis-
played. If completed normally, "COMPLETE" is displayed.

Select 4 and press [START] key.

Press [CUSTOM SETTINGS] key.

40-7

Purpose

Adjustment/Setup

Function
(Purpose)

Used to enter the manual paper feed tray paper width 
adjustment value.

Section

Paper feed

Item

Operation

1

MAX. POSITION

Max. width

2

POSITION 1

Adjustment point 1

3

POSITION 2

Adjustment point 2

4

MIN. POSITION

Min. value

Press [START] key.

Press [CUSTOM SETTINGS] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.

1. MAX. POSITION

2. POSITION 1

3. POSITION 2

4. MIN. POSITION

1

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

MAX. POSITION ··· COMPLETE (or "ERROR")

Press [CUSTOM SETTINGS] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

POSITION 1 ··· COMPLETE (or "ERROR")

Select 1 and press [START] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

POSITION 2 ··· COMPLETE (or "ERROR")

Press [CUSTOM SETTINGS] key.

Press [CUSTOM SETTINGS] key. 

Select 2 and press [START] key.

Select 3 and press [START] key.

SIMULATION 40-2

BYPASS TRAY ADJUSTMENT.

MIN. POSITION ··· COMPLETE (or "ERROR")

SIMULATION 40-7

1

BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START.

1. MAX. POSITION :   

72

2. POSITION 1  :    

380

3. POSITION 2  :    

710

4. MIN. POSITION :  

804

SIMULATION 40-7

BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS

START.

1. MAX. POSITION

72

40-11

Purpose

Operation test/Check

Function
(Purpose)

Used to check the multi-purpose tray width detection
adjustment value.

Section

Paper feed

Item

Operation

M1SS1

Tray 3 size detection 1

M1SS2

Tray 3 size detection 2

M1SS3

Tray 3 detection size 3

M1SS4

Tray 3 size detection 4

TRAY3_WIDTH

Tray 3 guide plate position

TRAY3_AD

Tray 3 width detection volume output AD value

Tray3 width 
size

(Tray 3 width direction detection size is 
displayed.) A4/A3, 11X, B5/B4, 8.5X, A4R, B5R, 
A5R, 5.5X, 7.25X, EXTRA

40-12

Purpose

Adjustment/Setup

Function
(Purpose)

Used to check the multi-purpose tray width detection 
adjustment value.

Section

Paper feed

Item

Operation

1

SIMULATION 40-11

TRAY3 SENSOR CHECK..

M1SS1

     M1SS2     M1SS3     M1SS4

TRAY3_WIDTH: 

2100

        TRAY3_AD: 

600

(Tray3 width size: 

A4/A3

)

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов