Sharp AR-M550N Скачать руководство пользователя страница 218

Страница: 218 / 460

: Feb. 9 2004

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 3

3) Go through the modes specified in Simulation 8-2.

4) Select the number that corresponds to the adjustment item using

the numeric keypad.

5) Press the Start key.

6) Press the start key to have the voltage output for 30 seconds.

The operation can be stopped with the CUSTOM SETTINGS key.

If the output voltage is not within the requirement, do the following
steps.

7) Enter the adjustment value using the numeric keypad.

8) Press the Start key

(The adjustment value is put into memory, and the corresponding
voltage is output for 30 seconds.)

Repeat steps 7 to 8 until the output requirement is satisfied.

This adjustment is needed in the following situations:

• The high voltage power PWB (MC/DV/TC) has been replaced.

• U2 trouble has occurred.

• The PCU PWB has been replaced.

• The EEPROM of the PCU PWB has been replaced.

(Main charger grid voltage adjustment)

1) Remove the rear cover of the machine.

2) Apply a digital multi-meter to the connector CN2 pin (7) of the high

voltage PWB and the chassis GND.

3) Go through the modes specified in Simulation 8-1.

Press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

SIMULATION 8-2

MAIN GRID SETTING. SELECT 1-6, AND PRESS START.

1.AUTO

580

2.CHARACTER

580

3.MIX

580

4.PHOTO

580

5.PRINTER

580

6.FAX

580

SIMULATION 8-2

MAIN GRID SETTING. INPUT VALUE, AND PRESS START.

1.AUTO (200-1000)

580

SIMULATION 8-2

MAIN GRID SETTING. EXECUTING···.

1.AUTO

580

ADJ 1B

Adjust the developing bias voltage

Item/operation mode

Simulation

High voltage power PWB (MC/DV/TC)

Setting range

Default

Connector

Pin #

Actual voltage

Copy

Auto mode

8-1

AUTO

0 – 750

495

CN2

–500±5v

Text mode

CHARACTER

0 – 750

495

CN2

–500±5v

Text/photo mode

MIX

0 – 750

495

CN2

–500±5v

Photo mode

PHOTO

0 – 750

495

CN2

–500±5v

Printer

All modes

PRINTER

0 – 750

495

CN2

–500±5v

FAX

All modes

FAX

0 – 750

495

CN2

–500±5v

Cleaning mode

PLUS

0 – 250

150

CN2

+150±5v

CN2

Press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

SIMULATION 8-1

DV BIAS SETTING. SELECT 1-7, AND PRESS START.

1.AUTO

495

2.CHARACTER

495

3.MIX

495

4.PHOTO

495

5.PRINTER

495

6.FAX

495

7.PLUS

150

SIMULATION 8-1

DV BIAS SETTING. INPUT VALUE, AND PRESS START.

1:AUTO (0-750)

495

SIMULATION 8-1

DV BIAS SETTING. EXECUTING···.

1:AUTO

495

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 218 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: