Sharp AR-M550N, Руководство по обслуживанию, Страница: 415 / 460

: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 1
[12] OTHER
1. VARIOUS COUNTERS SPECIFICATIONS]
A. Count specification
(1) Paper exit system counter
Large size: A3, 11 x 17. (Greater size than paper length 384mm)
∗
( ): Count-up number when setting to the large size single count up.
(2) Document, finishing, paper feed system counter
Counter Count-up timing
Count-up number
Counter
reset
procedure,
clear
Simplex copy Duplex copy
Paper feed tray – Main
unit paper exit
Paper feed tray – ADU
ADU – Main unit paper
exit
Small size Large size Small size Large size Small size Large size
Total counter (Note) When transfer is completed 1 2 (1) 1 2 (1) 1 2 (1) —
Maintenance counter When transfer is completed 1 2 (1) 1 2 (1) 1 2 (1) Sim24-4
Developer counter When transfer is completed 1 2 (1) 1 2 (1) 1 2 (1) Sim24-5
All valid paper counter (Note) When paper exit 1 2 (1) — — 2 4 (2) —
Copy counter (Copy valid paper) When paper exit 1 2 (1) — — 2 4 (2) Sim24-6
FAX counter When paper exit 1 2 (1) — — 2 4 (2) Sim24-10
Print counter When paper exit 1 2 (1) — — 2 4 (2) Sim24-9
Internet FAX counter When paper exit 1 2 (1) — — 2 4 (2) Sim24-15
Document filing counter When paper exit 1 2 (1) — — 2 4 (2) Sim24-15
Right side paper exit counter When center paper exit 1 2 (1) — — 2 4 (2) —
Other counter (Self print, etc.) When paper exit 1 2 (1) — — 2 4 (2) Sim24-9
Counter Mode Count event Count-up condition
Counter reset
procedure,
clear
SPF counter All modes SPF paper
feed number Count is made when starting SPF paper pick.
Sim24-3
Finish stamp counter FAX send
Internet FAX send Finish stamp
use number Count is made when stamp is ON.
Sim24-3
Staple counter All modes
(Including inserter
stand alone process) Staple
number Count is made when bundle exit process is completed.
Double count is made when stapling two positions.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Punch counter All modes
(Including inserter
stand alone process) Punch
number Count is made when bundle exit process is completed.
1 count regardless of the kind of the punch unit (2-hole, 3-hole, etc.)
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Saddle staple counter All modes
(Including inserter
stand alone process) Saddle
staple
number Count is made when bundle paper exit process is c completed.
Only one count is added.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Scan total counter All modes Scan
number Count is made when scan is completed.
Sim24-3
ADU counter All modes ADU paper
feed number Count is made when paper feed from the ADU section is started.
Sim24-2
Inserter counter All modes
(Including inserter
offline process) Inserter tray
paper feed
number Count is made when paper feed from the inserter tray is started.
In the inserter stand alone mode, count is made when process is
completed.
Sim24-3
Paper
feed
counter Manual paper
feed tray All modes Tray paper
feed number Count is made when paper feed from each tray is started.
Sim24-2
Paper feed tray 1 Sim24-2
Paper feed tray 2 Sim24-2
Paper feed tray 3 Sim24-2
Paper feed tray 4 Sim24-2
LCC Sim24-2