Sharp AR-M550N Скачать руководство пользователя страница 350 | Manualshive

Страница: 350 / 460

Sharp AR-M550N Скачать руководство пользователя страница 350

: Feb. 9 2004

1

AR-M550/M620/M700 SIMULATION 8 - 92

Operation/Procedure

1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.

2) Press [START] key.

The signal is sent in the send level set with the soft SW.

When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.

Operation/Procedure

1) Select YES/NO of data transfer (backup).

2) Press [START] key.

This function is valid only when the AR-MM9 is installed.

Backup contents

The other contents are not backed up.

Operation/Procedure

1) Select YES/NO of data transfer.

2) Press [START] key.

Operation/Procedure

1) Enter the number corresponding to the information (item) to be

printed with 10-key.

2) Press [START] key.

66-18

Purpose

Setting

Function
(Purpose)

Used to check the dial signal (DTMF) output in the FAX
tone dial mode. An output is sent at the send level set
by the soft switch. Used to check the operation. (Only
when FAX is installed)

Section

FAX

Item

Operation

Press [START] key.

Press [CUSTOM SETTINGS] key.

66-19

Purpose

Data transfer

Function
(Purpose)

Used to back-up the HDD data into the Flash memory
(optional FAX expansion memory: AR-MM9). (Only
when FAX is installed)

Section

FAX

Item

Data

1

YES

Backup is executed.

2

NO

Backup is not executed.

• Address book data (FAX, Mail, Address)

• One-touch dial

• Item name

• FTP expansion

• Fine name

• Group expansion

• FAX receive select table

• Program

• IFAX receive YES/NO

• Use index

• Polling allow number

• Standard sender

• Memory box

• IFAX sender registration

• Sender name

• FAX sender registration

• Soft SW

SIMULATION 66-18

DTMF SIGNAL OUTPUT.(SOFT SW.) INPUT 0-9, *, #, AND PRESS

START.

1

SIMULATION 66-18

DTMF SIGNAL OUTPUT.(SOFT SW.) EXECUTING···.

1

66-20

Purpose

Data transfer

Function
(Purpose)

Used to read the back-up data by SIM 66-19 to the
SRAM/HDD. (Only when FAX is installed)

Section

FAX

Item

Data

1

YES

Backup is executed.

2

NO

Backup is not executed.

66-21

Purpose

Adjustment/Setup/Operation data output/Check
(Display/Print)

Function
(Purpose)

Used to print information related to FAX (various
registrations, communication management, file
management, system error protocol). (Only when FAX
is installed)

Section

FAX

Item

Data

1

REGISTERED

Various registration information

2

MANAGEMENT

Communication management
information

3

FILE MANAGEMENT

File management information

4

SYSTEM ERROR

System error information

5

PROTOCOL

Protocol information

SIMULATION 66-19

ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)

ARE YOU SURE?

1. YES

2. NO

SIMULATION 66-19

ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...

1

1

Press [START] key.

After completion of backup

1

SIMULATION 66-20

ADDRESS DATA BACK UP. (READ FROM FLASH ROM)

ARE YOU SURE?

1. YES

2. NO

SIMULATION 66-20

ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING...

1

1

Press [START] key.

After completion of read

«
...
348
349
350
351
352
...
»

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов