manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 285 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 285

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 27

Operation/Procedure

1) Select the number corresponding to the operating condition of

aging with 10-key.

The combined mode of 0 - 6 mode and 10, 20, or 30 mode can be
set.

In that case, the number corresponding to one of 0 - 6 mode and
the number corresponding to one of 10, 10, and 30 mode are
added and the sum number is entered.

2) Press [START] key.

The condition selected in procedure 1) is set.

The setting of this simulation is kept valid until the power is turned off.

Operation/Procedure

1) Enter the intermittent aging cycle (unit: sec) with 10-key.

2) Press [START] key.

The time entered in procedure 1) is set.

∗

Set range of interval time: 1 - 999 (sec)

Set the intermittent aging mode cycle of 7-1 with 10-key. (Unit: sec)

Operation/Procedure

1) Select the number corresponding to the warm-up time display

YES/NO.

2) Press [START] key, and the number selected in procedure 1) is

set.

∗

The setting of this simulation is kept valid until the power is turned
off.

The warm-up time is displayed in the unit of second.

Operation/Procedure

1) Enter the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is stored, and the output corresponding to the set
value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

(The developing bias output voltage adjustment and output check can
be made in each print mode.)

7

7-1

Purpose

Setting

Function
(Purpose)

Used to set the operating conditions of aging.

Section

Item

Operation

0

NO MISS FEED DETECTION

No jam detection

1

AGING

Aging mode

2

AGING/NO MISS FEED 
DETECTION.

No jam detection, aging 
mode

3

AGING/NO MISS FEED 
DETECTION/NO WARM UP/
NO TEMPERATURE 
CONTROL.

No jam detection/ no warm-
up/ no fusing temperature 
control, aging mode

4

NO WARM UP.

No warm-up 

5

AGING/INTERVAL.

Intermittent aging mode

6

AGING/INTERVAL/NO MISS 
FEED DETECTION.

No jam detection 
intermittent aging mode

+10

NO PROCESS UNIT CHECK.

Above +10: No process unit 
(including the developing 
unit) detection

+20

NO SHADING.

Above +20: No shading

+30

NO PROCESS UNIT CHECK/
NO SHADING.

Above +30: No process unit 
detection /no shading

Press [START] key to start registration and operation. 
The operation mode is kept until the power is turned off or setting is made again. 

7-6

Purpose

Setting

Function
(Purpose)

Used to set the intermittent aging cycle.

Section
Item

Operation

SIMULATION 7-1

AGING TEST SETTING. SELECT 0-36, AND PRESS START.

0.NO MISS FEED DETECTION

1.AGING

2.AGING/NO MISS FEED DETECTION.

3.AGING/NO MISS FEED DETECTION/

  NO WARM UP/NO TEMPERATURE CONTROL.

4.NO WARM UP.

5.AGING/INTERVAL.

6.AGING/INTERVAL/NO MISS FEED DETECTION.

+10:NO PROCESS UNIT CHECK.

+20:NO SHADING.

+30:NO PROCESS UNIT CHECK/NO SHADING.

    2

7-8

Purpose

Setting

Function
(Purpose)

Used to set the warm-up time display YES/NO.

Item

Operation

Warm-up is completed.

Press [CUSTOM SETTINGS] key.

8

8-1

Purpose

Adjustment/Operation test/Check

Function
(Purpose)

Used to check and adjust the operations of the 
developing voltage of each color and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

SIMULATION 7-6

INTERVAL AGING CYCLE SETUP. INPUT TIME AND PRESS START.

(1-999, UNIT: sec)

10

SIMULATION 7-8

WARM UP TIME DISPLAY. 

ARE YOU SURE?

1. YES

2. NO

1

Press [START] key, 
and time count is started.

SIMULATION 7-8

WARM UP TIME DISPLAY. WARMING UP,PLEASE WAIT.

(UNIT:sec)

 30 

Press [CUSTOME SETTING] key, 
and time count is stopped.

SIMULATION 7-8

WARM UP TIME DISPLAY. WARM UP COMPLETED.

(UNIT:sec)

 60 

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов