manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 198 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 198

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 143

b-2. Paper tray lift-up motor (Paper feed tray 2)

1) Remove the high voltage PWB unit. (See “a. Manual paper feed

drive unit” in the “[Manual paper feed drive section]”)

2) Disconnect the connector, and remove the lift-up motor unit.

3) Release the pawl, and remove the lift-up coupling. Remove the lift-

up spring from the lift-up motor.

b-3. Paper pickup solenoid (Paper feed tray 2)

1) Remove the high voltage PWB unit. (See “a. Manual paper feed

drive unit” in the “[Manual paper feed drive section]”)

2) Disconnect the connector, and remove the paper pickup solenoid

unit. 

3) Remove the paper pickup solenoid.

∗

When installing, check that the solenoid plunger is inserted in the
arm.

[3/4 paper feed drive section]

(Replacement parts)

a. 3/4 paper feed drive unit

1) Remove the paper tray lift-up motor. (See “b-1. Paper tray lift-up

motor (Paper feed tray 3)” in this section)

2) Remove the parts and remove the drive joint plate.

∗

When installing, be careful of the direction of the belt holding sheet.

∗

When installing, temporarily fix the 1/2 paper feed drive unit to the
main unit, and install the drive joint plate. Then tighten the screw of
the drive unit securely. 

3) Remove the external outfit mounting plate.

No.

Unit

Parts

a

3/4 paper feed drive unit

1

Paper feed clutch (Paper feed 
tray 3)

2

Paper feed clutch (Paper feed 
tray 4)

3

Paper feed tray 3/4 paper 
transport clutch 1

b

Other

1

Paper tray lift-up motor (Paper 
feed tray 3)

2

Paper tray lift-up motor (Paper 
feed tray 4)

b-1

b-2

a-2

a

a-1

a-3

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов