Sharp AR-M550N Скачать руководство пользователя страница 63

Страница: 63 / 460

: Feb. 6 2004

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 8

B. Maintenance and parts replacement

(1) Maintenance list

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

(2) Maintenance and parts replacement

(List of Replacement Parts)

AR-M550U/N (PM: 250K)

When

calling

250K 500K 750K 1000K 1250K 1500K 1750K 2000K

Remark

AR-M620U/N, AR-M700U/N
(PM: 300k)

300K 600K 900K 1200K 1500K 1800K 2100K 2400K

Unit name No.

Part name

Multi manual
paper feed

Pickup roller

(Note 1)

Paper feed roller

(Note 1)

Separation roller

(Note 1)

Torque limiter

(Note 1)

Shaft (Conduction grease)

✩

UKOG-0012QSZZ

(Note 1)

Replacement reference: For replacement, refer to each paper feed port counter value.

Manual paper feed : 100K or 1 year
Torque limiter

: 800K (However, 400K for manual paper feed section)

No.

Unit

Parts

Multi manual paper
feed tray unit

Manual paper feed unit open/
close switch

Manual feed empty detector

Pickup roller

Paper feed roller

Separation roller

Torque limiter

Manual feed gate solenoid

Manual feed paper pass
detector 1

Paper feed clutch

Paper pickup solenoid

Manual feed paper width size
detection PWB

Manual feed paper length
detector 1

Manual feed paper length
detector 2

Manual tray pull-out position
detector 1

Manual tray pull-out position
detector 2

a-1

a-2

a-7

a-8

a-9

a-10

a-11

a-12

a-13

a-14

a-15

a-6

a-3

a-4

a-5

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 63 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: