manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 219 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 219

: Feb. 9 2004

1

AR-M550/M620/M700  SETTING AND ADJUSTMENTS  7 - 4

4) Select the number that corresponds to the adjustment item using

the numeric keypad.

5) Press the Start key. 

6) Press the start key to have the voltage output for 30 seconds. 

The operation can be stopped with the CUSTOM SETTINGS key. 

If the output voltage is not within the requirement, do the following
steps. 

7) Enter the adjustment value using the numeric keypad. 

8) Press the Start key

(The adjustment value is put into memory, and the corresponding
voltage is output for 30 seconds.) 

Repeat steps 7 to 8 until the output requirement is satisfied.

(Transfer voltage adjustment)

Transfer voltage adjustment (print operation mode)

This adjustment is needed in the following situations: 

• The high voltage power PWB (MC/DV/TC) has been replaced.

• U2 trouble has occurred. 

• The PCU PWB has been replaced.

• The EEPROM of the PCU PWB has been replaced. 

1) Go through the modes specified in Simulation 8-6.

2) Select the number that corresponds to the adjustment item

(FRONT/BACK) using the numeric keypad.

3) Press the Start key

4) Enter the adjustment value (default) using the numeric keypad.

5) Press the Start key

The operation can be stopped with the CUSTOM SETTINGS key.

Note: It is not possible to determine the adjusted transfer voltage

(print operation mode) (FRONT/BACK). If the voltage seems to
be abnormal after setting the default value, therefore, the high
voltage PWB (MC/DV/TC) should be replaced.

Transfer voltage adjustment (transfer belt cleaning mode)

This adjustment is needed in the following situations: 

• The high voltage power PWB (MC/DV/TC) has been replaced.

• U2 trouble has occurred. 

• The PCU PWB has been replaced.

• The EEPROM of the PCU PWB has been replaced. 

1) Remove the rear cover of the machine.

2) Apply a digital multi-meter to the connector CN2 pin (1) of the high

voltage PWB and the chassis GND. 

ADJ 1C

Adjust the transfer voltage

Item/operation 

mode

Simulation

Adjustment voltage 

(monitor voltage)

Connector

Pin #

Actual voltage/actual 

current

Setting range

Default

Front print

8-6

FRONT

0 – 800

350

–

–

–

35±1.0

µ

A (1.0 – 1.5Kv)

High voltage 
power PWB 
(MC/DV/TC)

400*

40±1.0

µ

A (2.0 – 2.5Kv)*

Back print

BACK

0 – 800

350

–

–

–

35±1.0

µ

A (1.0 – 1.5Kv)

400*

40±1.0

µ

A (2.0 – 2.5Kv)*

Transfer belt 
(cleaning)

8-17

SHF FRONT

0 – 600

450

–

–

–

AC4.5Kv (p-p)

SHF BACK

0 – 600

450

–

–

–

AC4.5Kv (p-p)

THV-

0 – 75

10

DC -100±10v

CN2

1

DC -100±10v /
AC4.5Kv (p-p)

Transfer roller 
(cleaning)

8-18

CRHV PLUS

0 – 250

200

+2.0±0.1v

–

Check pin +2000±100v

High voltage 
power PWB 
(TC cleaning)

Transfer roller 
(print)

CRHV MINUS

0 – 250

200

–2.0±0.1v

–

Check pin –2000±100v

1

1

1

*: AR-M700N/U

1

Press [START] key.

Press [CUSTOM SETTINGS] key. 

Press [START] key.

Press [CUSTOM SETTINGS] key. 
Or after 30sec output.

SIMULATION 8-6

1

THV+ SETTING. SELECT 1-2, AND PRESS START.

1.FRONT 

300

2.BACK  

300

SIMULATION 8-6

THV+ SETTING. INPUT VALUE, AND PRESS START.

1.FRONT(0-800)

300

SIMULATION 8-6

THV+ SETTING. EXECUTING···.

1.FRONT

300

(The adjustment value is put into memory, and the corresponding
current is output for 30 seconds.)

1

CN2

1

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов