Sharp AR-M550N Скачать руководство пользователя страница 100

Страница: 100 / 460

: Feb. 6 2004

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 45

C. Maintenance and parts replacement

(1) Maintenance list

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

Code

Signal

name

Name

Function/Operation

Type

Note

POD1

Paper exit detector 1

Paper exit detection from fusing

Transmission
type

Paper transport system sensor

POD2

Paper exit detector 2

Paper pass detection from paper exit

Transmission
type

Paper transport system sensor

POD3

Paper exit detector 3

Paper exit detection to upper section
paper exit tray (Full detection)

Transmission
type

Paper transport system sensor

POM1

Paper exit motor 1

Drives the paper transport roller 16.

Stepping
motor

Selection of Normal speed/
High speed

POM2

Paper exit motor 2

Drives the paper exit roller 1.

Stepping
motor

Selection of Normal speed/
High speed/ Reverse rotation

CFM-U1 CFM-U1

Fusing cooling fan motor 1
(Paper exit, duplex (ADU) section)
(Front surface)

Discharges heat generated in the
fusing section.

DC brushless
motor

PWM control

CFM-U3 CFM-U3

Fusing cooling fan motor 3
(Paper exit, duplex (ADU) section)
(Front surface)

Discharges heat generated in the
fusing section.

DC brushless
motor

PWM control

CFM-U4 PWM-RSV1 Fusing cooling fan motor 4

(Paper exit, duplex (ADU) section)
(Paper exit section rear side)

Cools paper which is discharged to
the inner tray.

DC brushless
motor

PWM control

INTPWB

Paper exit temperature sensor

Paper exit section temperature
detection

No.

Name

Function

Transport roller 16

Transports paper from the fusing roller to the paper exit roller 1.

Paper exit roller 1

Discharges paper to the paper exit tray. / Switchbacks paper.

AR-M550U/N (PM: 250K)

When

calling

250K 500K 750K 1000K 1250K 1500K 1750K 2000K

Remark

AR-M620U/N, AR-M700U/N
(PM: 300k)

300K 600K 900K 1200K 1500K 1800K 2100K 2400K

Unit name

No.

Part name

Paper exit
reverse section

Transport rollers

❍

Transport paper guides

❍

Discharge brush

Shaft (Conduction grease)

UKOG-0012QSZZ

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 100 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: