manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 308 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 308

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 50

Operation/Procedure

Operation/Procedure

The output levels of the temperature sensor and the humidity sensor in
the developing unit are displayed.

Operation/Procedure

Operation/Procedure

1) Select the number corresponding to the copy mode to be adjusted

with 10-key. (Select one of 3 - 6.)

2) Press [START] key.

3) Enter the copy density level with 10-key.

LD ADJ

Actual laser power beam 
(Including correction)

AUTO

Auto copy mode

CHARA

Text copy mode

CHARA P

Text/Photo copy mode

PHOTO

Photo copy mode

PRT

Printer mode

DESTINATION 1

Toner destination code stored 
in the main unit

DESTINATION 2

Toner destination code stored 
in the toner bottle CRUM chip

44-12

Purpose

Adjustment/Setup/Operation data output/Check 
(Display)

Function
(Purpose)

Used to display sampling toner image patch density 
data in image density correction. (Used to check that 
the correction is performed normally or not.)

Section

Image process (Photoconductor/Developing)

Item

Operation

DMLED

OPC drum marking sensor LED current adjustment 
value

PC LED

OPC drum marking sensor LED current adjustment 
value

END DV BS

Developing bias voltage when making PT2/BS2 of ID 
(1)

ID (n)

Indicates the toner patch making procedures. 

PT1/BS1

Toner patch density detection level/OPC drum surface 
detection level when the developing bias is 0V - 50V.

PT2/BS2

Toner patch density detection level/OPC drum surface 
detection level when the developing bias is 0V.

PT3/BS3

Toner patch density detection level/OPC drum surface 
detection level when the developing bias is 0V + 50V.

44-14

Purpose

Adjustment/Setup/Operation data output/Check 
(Display)

Function
(Purpose)

Used to check the output level of the temperature 
sensor and the humidity sensor.

Section

Image process (Photoconductor/Developing)

Item

Operation

Item

NOTE

SIMULATION 44-9

PROCESS CONTROL DATA DISPLAY.
DRUM ROTATION TIME: 

01234567

(sec)

DEVE MIXING TIME: 

01234567

(sec)

DRUM: 

0

         GR_BS           DV_BS            LD_ADJ
AUTO     

000/000

         000/000          000/000

CHARA    

000/000

         000/000          000/000

CHARA_P  

000/000

         000/000          000/000

PHOTO    

000/000

         000/000          000/000

PRT      

000/000

         000/000          000/000

DESTINATION1: 

0

          DESTINATION2: 

0

SIMULATION 44-12

DM DATA, PATCH/BASE DATA DISPLAY.
DMLED: 

000

    PC LED: 

000

    END DV_BS: 

000

 

         PT1/BS1      PT2/BS2      PT3/BS3
ID(1):   

000/000

      000/000      000/000

ID(2):   

000/000

      000/000      000/000

ID(3):   

000/000

      000/000      000/000

ID(4):   

000/000

      000/000      000/000

ID(5):   

000/000

      000/000      000/000

ID(6):   

000/000

      000/000      000/000

ID(7):   

000/000

      000/000      000/000

ID(8):   

000/000

      000/000      000/000

TH-DV (Not used)

Developing section temperature 
sensor

0 - 255

TH-RA (Not used)

Room temperature sensor

0 - 255

TH-CL

Process section temperature sensor

0 - 255

TH-EX

Paper discharging section 
temperature sensor

0 - 255

HUS-DV

Developing section humidity sensor

0 - 255

HUS-TC (Not used)

Process section humidity sensor

0 - 255

44-16

Purpose

Adjustment/Setup/Operation data output/Check 
(Display)

Function
(Purpose)

Used to check the toner concentration control data.

Section

Image process (Developing)

Item

Operation

HUMIDITY AREA

Humidity area

INT HUMIDITY 
AREA

Humidity area when setting the toner 
concentration control level (SIM 25-2)

TARGET LEVEL

Current toner concentration control level

DEV REF

Toner concentration when setting the toner 
concentration control level (SIM 25-2)

HUMIDITY 
(TARGET)

Toner concentration correction value for 
humidity

A

Toner concentration correction value for change 
in developing bias voltage

B

Toner concentration value for developer life

46

46-2

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy density in all the copy modes 
(Auto, Text, Text/Photo, and Photo mode).

Section
Item

Picture quality

Density

SIMULATION 44-14

SENSOR DATA DISPLAY MONITOR.
TH-DV:      

255

TH-RA:      

255

TH-CL:      

255

TH-EX:      

255

HUS-DV:     

255

HUS-TC:     

255

1

SIMULATION 44-16

TONER CONTROL STANDARD LEVEL DISPLAY.
HUMIDITY AREA: 

31

INT HUMIDITY AREA: 

31

TARGET LEVEL = DEV REF + HUM(TARGET) + A + B
       

146

   = 

128

     + 

10

(

12

)      + 

5

 + 

3

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов