manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 11 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 11

: Feb. 9 2004

1

AR-M550/M620/M700  SPECIFICATIONS  3 - 2

2. Engine specifications

A. Paper feeding, paper conveyance, and discharge section

(1)

Paper feeding performance

• Tray 1 (Left tray in the parallel LCC)

*1: Time required from tray insertion to empty detection when paper is empty.

• Tray 2 (Right tray in the parallel LCC)

*1: Time required from tray insertion to empty detection when paper is empty.

• Tray 3 (Multi-purpose tray)

*1: For 105g/m

2

 or above, A4/8.5 x 11 or less. For 128g/m

2

 or above, horizontal feed only.

*2: For multi copy and back surface copy, single feed only.

• Tray 4 (500-sheet paper feed tray)

*1: For 105g/m

2

 or above, A4/8.5 x 11 or less. For 128g/m

2

 or above, horizontal feed only.

*2: For multi copy and back surface copy, single feed only.

Type

4-stage paper feed tray (Parallel LCC + 2 tray + Multi manual paper feed)

Paper feed method

Paper is fed from the above by the front loading system.

Dehumidification heater

Japan

Standard

Except for Japan Option

Paper size

(set by software)

Paper size 

change method

Paper type 

setting

Paper size setting 

when shipping

Allowable paper 

type and weight 

for paper feed 

Paper capacity 

(Standard paper)

Paper type

Paper 

remaining 

detection

Tray lift time

A4, 8.5" x 11"

Size setting by 
user

YES

Japan: A4
Inch Series:
8.5" x 11"
AB Series: A4 (16K 
is not supported.)

Normal paper: 
60 – 105g/m

2

 

(16 – 28lbs)

Japan: 900 
sheets (64g/m

2

)

Except for Japan: 
800 sheets 
(80g/m

2

)

Normal paper, printed 
paper, recycled, 
letterhead, punched 
paper, color paper

Enable 
(Paper 
empty and 3 
steps)

Up

Within 
12sec *1

Down

Free fall

1

Paper size (set by 

software)

Paper size 

change method

Paper type 

setting

Paper size setting 

when shipping

Allowable paper 

type and weight 

for paper feed 

Paper capacity 

(Standard paper)

Paper type

Paper 

remaining 

detection

Tray lift time

Japan:

A4, B5, 8.5" x 11"

AB series (Europe, 
SCA):

A4, 8.5" x 11"

AB series (Other):

A4, B5, 8.5" x 11"

Inch Series:

8.5" x 11", A4

Size setting by 
serviceman
(B5 available 
through bolt 
fixing and 
setting by 
serviceman)

YES

Japan: B5
Inch Series:
8.5" x 11"
AB Series: A4 
(16K is not 
supported.)

Normal paper:
60 – 105g/m

2 

(16 – 28lbs)

Japan: 1300 
sheets (64g/m

2

)

Except for Japan: 
1200 sheets 
(80g/m

2

)

Normal paper, 
printed paper, 
recycled, letterhead, 
punched paper, color 
paper

Enable 
(Paper 
empty and 
3 steps)

Up

Within 
12sec *1

Down

Free fall

Paper size

Paper size 

change method

Paper type 

setting

Paper size 

setting when 

shipping

Allowable paper 

type and weight 

for paper feed 

Paper capacity 

(Standard paper)

Paper type

Document detection

Paper 

remaining 

detection

A3, B4, A4, A4R, B5, 
B5R, A5R, 8K, 16K, 
16KR
11 x 17, 8.5 x 14, 
8.5 x 13, 8.5 x 11, 
8.5 x 11R, 7.25 x 
10.5R, 5.5 x 8.5R, 
Special size (Tab 
paper is of A4; limited 
to tab width 12mm –  
20mm/8.5 x 11; tab 
width 6.1mm – 
17mm.)

Guide 
adjustment by 
user

YES

Shipped with 
the paper 
guide width 
at Max.

Normal paper: 
60 – 105g/m

2 

(16 – 28 lbs)
Thick paper: 
106 – 128g/m

2

 

(29 – 34 lbs)
205g/m

2

 (110 lbs)

176g/m

2

 (65 lbs)

OHP, label sheet, 
tab paper *1, *2

Standard 
paper

Japan: 550 
sheets 
(64g/m

2

)

Except for 
Japan: 500 
sheets 
(80g/m

2

)

Normal paper, 
printed paper, 
recycled, 
letterhead, 
punched paper, 
color paper, thick 
paper, label 
sheet, OHP, tab 
paper

Automatic 
detection
Auto-AB

A3, B4, A4, 
A4R, B5, 
B5R, 
8.5 × 13

Enable 
(Paper 
empty 
and 3 
steps)

OHP

40 sheets

Automatic 
detection
Auto-inch

11 × 17, 
8.5 × 14, 
8.5 × 11, 
8.5 × 11R, 
7.25 × 
10.5R

Tab paper Enable

For 8K, 16K, and 16KR, 
setting is made 
manually. 
Detection 
disregard 
setting 

Enable

Paper size

Paper size 

change 
method

Paper 

type 

setting

Paper size 

setting when 

shipping

Allowable paper 

type and weight 

for paper feed 

Paper capacity 

(Standard paper)

Paper type

Document detection

Paper 

remaining 

detection

A3, B4, A4, A4R, 
B5, B5R, 8K, 16K, 
16KR
11 × 17, 8.5 × 14, 
8.5 × 13, 
8.5 × 11, 
8.5 × 11R, 
7.25 × 10.5R

Guide 
adjustment by 
user

YES

Shipped with 
the paper 
guide width 
at Max.

Normal paper: 
60 – 105g/m

2 

(16 – 28 lbs)
*1, *2
Thick paper: 
106 – 128g/m

2 

(29 – 34 lbs)
205g/m

2

 (110 lbs)

176g/m

2

 (651 lbs)

Japan: 550 
sheets (64g/m

2

)

Except for 
Japan: 500 
sheets (80g/m

2

)

Normal paper, 
printed paper, 
recycled, 
letterhead, 
punched paper, 
color paper, thick 
paper

Automatic 
detection
Auto-AB

A3, B4, A4, A4R, 
B5, B5R, 8.5×13

Enable 
(Paper 
empty and 
3 steps)

Automatic 
detection
Auto-inch

11 × 17, 8.5 × 14, 
8.5 × 11, 8.5 × 11R, 
7.25 × 10.5R

For 8K, 16K, and 16KR, setting is 
made manually. 

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов