Sharp AR-M550N Скачать руководство пользователя страница 149

Страница: 149 / 460

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 94

(2) Maintenance and parts replacement

(Replacement parts)

a. Scanner unit

1) Remove the SPF unit. (See “a. SPF unit” in the “SPF section”)

2) Remove the table glass. (See “a-1. Table glass” in this section)

3) Remove the panel lock connector. (For dehumidifier heater)

4) Remove the flat cable, the connector, and harness from the cable

clamp.

5) Remove the right side cabinets upper and lower.

6) Remove the screw and the fixing plate.

No.

Unit

Parts

Scanner
unit

Table glass

❍

Slit glass (SPF scan mode)

❍

Mirror

❍

Lens

❍

Reflector

❍

Scanner dry heater

Rails

✩

Drive belt

Drive wire

Pulley

Scanner
unit

Scanner lamp

❍

Inverter PWB

CCD lens unit

❍

Scanner relay PWB

Scanner motor

Scanner FLASH PWB

Scanner control PWB

SPF open/close detector

Scanner home position sensor
detector

Document size detection light emitting
PWB

Document size detection light
receiving PWB

a-1

a-2

a-3

a-8

a-4

a-5

a-6

a-9

a-7

a-10

a-11

a-12

a-13

a-14

a-15

a-16

a-17

a-18

a-19

a-20

a-21

a-22

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 149 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: