Sharp AR-M550N Скачать руководство пользователя страница 77

Страница: 77 / 460

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 22

B. Operational descriptions

(1) Each paper feed tray paper size detection method

a. Multi-purpose paper feed tray (Tray 3), paper feed tray (Paper

feed tray 4)

1) Paper width detection

The paper width is calculated with the VR voltage value (A/D con-
version value) linked with the side guide plate.

Paper width and paper size (set in the range of standard value
±6 [mm]).

2) Paper size detection

The paper size detection is made by the combination of the cas-
sette paper size detector 1 to 4.

Relationship Between Paper Size and Detection by the Paper Size Detector

3) Combination of size detection

Width size

detection pattern

Paper size

Standard

value [mm]

Range [mm]

A3/A4

297.0

303.0 - 291.0

WLT/LT

279.4

285.4 - 273.4

B4/B5

257.0

263.0 - 251.0

LG/LTR/Foolscap

215.9

221.9 - 209.9

A4R

210.0

216.0 - 204.0

Exective-R

184.1

190.1 - 178.1

B5R

182.0

188.0 - 176.0

CSS2

CSS1

CSS3

CSS4

Vertical size

detection pattern

Detection SW status

AB size

Inch size

Width of detection

range

CSS1

CSS2

CSS3

CSS4

OFF

Extra

147.0 - 198.0

OFF

198.0 - 237.0

OFF

B5R

EX-R

237.0 - 274.0

OFF

A4R

LTR

274.0 - 314.0

OFF

Foolscap

Extra

314.0 - 347.0

OFF

LGL

347.0 - 389.0

OFF

WLT

389.0 - 432.8

OFF

Paper feed tray not attached

Paper size

Width detection pattern

Vertical detection pattern

B5R

A4R

Foolscap

EX-R

LTR

LGL

WLT

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 77 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: