Sharp AR-M550N Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 460

Sharp AR-M550N Скачать руководство пользователя страница 12

: Feb. 9 2004

1

AR-M550/M620/M700 SPECIFICATIONS 3 - 3

• Manual paper feed

*1: For paper exceeding 105g/m

2

, A4/8.5 x 11 or smaller. For paper exceeding 128g/m

2

, horizontal feed only.

*2: Multi-back surface copy is enable only in single feed.

• Duplex

(2)

Finishing performance

B. Scanner section (read)

(1)

Type

(2)

Original standard position, scanning size, and
scanning area

a. Original standard position

b. Scanning size

(3)

Resolution

* Except for FAX sending

(4)

Gradation

(5)

Scanning speed

(6)

Light source

(7)

Scanning sensor

Paper size

Paper type

setting

Allowable paper type and

weight for paper feed

Paper capacity

(Standard paper)

Paper type

Document detection

Paper empty

detection

A3, B4, A4, A4R,
B5, B5R, A5R, 8K,
16K, 16KR,
Postcard
11×17, 8.5×14,
8.5×13, 8.5×11,
8.5×11R,
7.25×10.5R,
5.5×8.5R

YES

Thin paper: 52 – 59g/m

2

(14 – 15lbs) (Tab paper in
single feed)
Normal paper:
60 – 105g/m

2

(16 – 28 lbs)

Thick paper:
106 – 128g/m

2

(29 – 34 lbs),

176g/m

2

(65 lbs) cover

205g/m

2

(110 lbs) Index

OHP, postcard,
label sheet, tab paper*1, *2

Plain paper : 100
sheets (80g/m

2

)

Postcard: 20
sheets
OHP: 20 sheets

Normal paper, recycled
paper, printed paper,
punched paper, color
paper, letterhead, back
paper, label paper, thick
paper, OHP, tab paper (tab
width 20mm or less)

Automatic
detection
Auto-AB

A3, B4, A4, A4R, B5, B5R,
Postcard, A5R

YES

Automatic
detection
Auto-inch

11×17, 8.5×14, 8.5×13,
8.5×11, 8.5×11R,
7.25×10.5R, 5.5×8.5R

Detection of 8K and 16K in the manual
paper feed tray is not performed.

System

Non stack system

Paper size

A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K,
16KR, 11 x 17, 8.5 x 14, 8.5 x 13, 8.5 x 11, 8.5
x 11R, 8.5 x 5.5R

Type and weight of
paper which can be
passed

Plain paper: 60 – 105g/m² (16 – 28lbs)
Thick paper: 106 – 128g/m² (29 – 34 lbs),
176g/m² (65 lbs cover)
205g/m² (110 lbs) Index

Paper exit position /
system

Main unit top surface face-down paper exit

Paper exit capacity

250 sheets (80g/m

2

paper)

Paper exit paper size/
kind

All kinds of paper which can be fed

Remaining paper
detection

None

Paper exit paper full
detection

Provided

Document table mode / SPF (front side) mode
Scanning method By the CCD image sensor.

SPF (back side) mode
Scanning method By the CIS image sensor

Document table

Left bottom reference

SPF

Center reference

Max. original size AB Series

A3

Inch Series

11 × 17

Scan
resolution
(dpi)

Copy mode

Platen

Magnification
ratio

25 – 99

Normal

ratio

101 – 171

172 – 400

600 × 600

600 × 600

600 × 600

600 ×

(600 × 2)

SPF

Magnification
ratio

25 – 99

Normal

ratio

101 – 117

118 – 200

When in
single copy

600 × 367

600 × 367

600 × 367

600 × 600

When in
duplex copy
(front) CCD

600 × 600

600 × 600

600 ×

(600 × 2)

600 ×

(600 × 2)

When in
duplex copy
(back) CIS

600 × 300

600 × 300

600 × 600

600 × 600

Input and
send
resolution
(dpi)

When in the Fax send mode and the scanner FAX broadcast mode

Select mode

Standard

Fine

text

Super

fine test

Ultra

fine text

600dpi

send *

Input resolution:
OC

600 × 600

600 ×

600

600 ×

600

600 × 600

Input resolution:
SPF simplex

600 × 367

600 ×

367

600 ×

367

600 × 367

Input resolution:
SPF simplex
(front) CCD

600 × 600

600 ×

600

600 ×

600

600 × 600

Input resolution :
SPF duplex
(back) CIS

600 × 300

600 ×

300

600 ×

300

600 × 300

Communication
resolution

FAX

203.2 ×

97.8

203.2 ×

195.6

203.2 ×

391

406.4 ×

391

–

Internet FAX

200 × 100

200 ×

200

200 ×

400

400 ×

400

600 ×

600

Input and
send
resolution
(dpi)

Scanner mode

Select mode

200 × 200

300 × 300

400 × 400

600 × 600

Input resolution:
OC

600 × 600

600 × 600

600 × 600

600 × 600

Input resolution:
SPF simplex

600 × 367

600 × 367

600 × 367

600 × 367

Input resolution:
SPF duplex
(front) CCD

600 × 600

600 × 600

600 × 600

600 × 600

Input resolution:
SPF duplex
(back) CIS

600 × 300

600 × 300

600 × 300

600 × 300

Communication
resolution

200 × 200

300 × 300

400 × 400

600 × 600

Input

Output

256 gradations (8bit)

2 gradations (1bit)

Scans per minute

DSPF

65 surfaces (single)
76 surfaces (duplex)

Type

None-electrode xenon lamp (Front), LED (Back)

Type

Monochrome CCD

1

«
...
10
11
12
13
14
...
»

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов