manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 189 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 189

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 134

(2) Maintenance and parts replacement 

[Fusing drive section]

(Replacement parts)

a. Fusing drive unit

1) Remove the fusing unit. (See “a. Fusing unit” in the “6. Fusing sec-

tion”)

2) Remove the fusing motor. (See “b-1. Fusing motor” in this section)

3) Disconnect the connector and remove the harnesse clamp.

4) Remove the fusing drive unit.

∗

Remove the screw which was indicated with the arrow mark.

a-1. Paper exit motor 1

a-2. Paper exit motor 2

1) Remove the fusing unit. (See “a. Fusing unit” in the “6. Fusing sec-

tion”)

2) Remove the fusing drive unit. (See “b-1. Fusing motor” in this sec-

tion)

3) Disconnect the connector, and remove the fusing drive frame.

4) Remove the paper exit motor 1 (A) and the paper exit motor 2 (B).

b-1. Fusing motor

1) Remove the rear cabinet and the rear cabinet upper.

No.

Unit

Parts

a

Fusing drive unit

1

Paper exit motor 1

2

Paper exit motor 2

b

1

Fusing motor

b-1

a-1

a-2

a

1

1

A

B

1

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов