manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 292 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 292

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 34

Operation/Procedure

1)The ROM version of each section can be checked. When there is
any problem in the software, use this simulation to check the ROM ver-
sion of each section and revise the version if necessary.

Operation/Procedure

When installing or servicing this machine, execute this simulation to
print and save various setting and adjustment data for next servicing.
(For example, memory trouble, PWB replacement, etc.)

1) Enter 1 with 10-key.

2) Press [START] key.

The various setting and adjustment data are printed out. (The print
paper cannot be selected optionally.)

Operation/Procedure

The key operator code is displayed.

Operation/Procedure

The values of the finisher counter, the scanner (read), counter, and the
SPF related counters are displayed.

Operation/Procedure

The values of the paper feed related counters are displayed. 

22-5

Purpose

Other

Function
(Purpose)

Used to check the ROM version of each unit (section).

Section

Item

Software

S/N

Engine section serial number

MFP

MFP controller

(LANGUAGE)

(Language version)

BOOT

MFP controller BOOT ROM

FAX

FAX controller

PCU

PCU controller

SCANNER

Scanner controller

FINISHER

Finisher controller

SADDLE UNIT

Saddle unit

LCC

Side LCC

INSERTER

Inserter

22-6

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to output the list of the setting and adjustment 
data (simulations, FAX soft switch, counters).

Section

Item

Data

Adjust/Setting data

0

TRAY SELECT

TRAY SELECT auto only (Selection is not 
allowed.)

1

PRINT START

PRINT START

Select 1 and press 
[START] key.

Press [CUSTOMSETTING] key or [START] 
key.

SIMULATION 22-5

ROM VERSION DATA DISPLAY.

S/N:   0000000000

MFP:           1.00   (LANGUAGE:  1.00)

PCU:           1.00            BOOT:      1.00

SCANNER:       1.00             FAX:      1.00

FINISHER:      1.00

SADDLE UNIT:   1.00             LCC:      1.00

INSERTER:      1.00

SIMULATION 22-6

DATA PRINT MODE. SELECT SETTING, AND PRESS START.

0. TRAY SELECT  :AUTO ONLY

1. PRINT START

1

SIMULATION 22-6

0

DATA PRINT MODE. EXECUTING···.

0. TRAY SELECT  :

1

22-7

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to display the key operator code. (This simulation 
is used when the customer forgets the key operator 
code.)

Section

Item

Data

User data

22-8

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to check the number of use of the finisher, the 
SPF, and the scan (reading) unit.

Section

Optical (Image scanning)

Finisher

Item

Counter

SPF

Document feed quantity

SCAN

Number of scans

STAPLER

Number of stapling

PUNCH

Number of punching

STAMP

Number of SPF finish stamps

SADDLE STAPLER

Number of saddle staples

INSERTER

Number of inserter operations

22-9

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to check the number of use (print quantity) of 
each paper feed section.

Section

Paper feed, ADU

Item

Counter

TRAY1

Tray 1 use quantity 

TRAY2

Tray 2 use quantity

TRAY3

Tray 3 use quantity

TRAY4

Tray 4 use quantity

BPT

Manual feed tray use quantity

ADU

Duplex paper feed quantity

LCC

Side LCC use quantity

SIMULATION 22-7

KEY OPERATOR CODE DISPLAY.

CODE: *****

SIMULATION 22-8

ORG./STAPLE COUNTER DATA DISPLAY.

SPF: ********

SCAN: ********

STAPLER: ********      PUNCH: ********

STAMP: ********        SADDLE STAPLER: ********

INSERTER: ********     INSERTER OFF LINE: ********

SIMULATION 22-9

PAPER FEED COUNTER DATA DISPLAY.

TRAY1: ********   TRAY2:********

TRAY3: ********   TRAY4:********

BPT: ********    ADU: ********

LCC: ********

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов