manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 401 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 401

: Feb. 9 2004

1

AR-M550/M620/M700  MAINTENANCE LIST  11 - 2

(Document scan section)

Transport 
section/
paper exit 
reverse 
section/
duplex section

1

PS follower roller

✕

❍

❍

❍

❍

❍

❍

❍

❍

2

Transport rollers

✕

❍

❍

❍

❍

❍

❍

❍

❍

3

Transport paper guides

❍

❍

❍

❍

❍

❍

❍

❍

❍

4

Discharge brush

✕

✕

✕

✕

✕

✕

✕

✕

✕

5

Shaft (Conductive grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0012QSZZ

6

Paper dust cleaner

❍

▲

▲

▲

▲

▲

▲

▲

▲

7

Sensors

❍

❍

❍

❍

❍

❍

❍

❍

❍

Optical reflection 
sensor

Drive section

1

Gear (Grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0307FCZZ

2

Gear (Grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0299FCZZ

3

Gear (Grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0062FCZZ

4

Gear (Grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0235FCZZ

5

Gear (Conductive grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0012QSZZ

6

Belts

✕

✕

✕

✕

✕

✕

✕

✕

Image-related 
sections

1

✕

✕

✕

✕

✕

✕

✕

✕

✕

AR-M550N/U (PM: 250K)

When 

calling 

250K 500K 750K 1000K 1250K 1500K 1750K 2000K

Remark

AR-M620N/U, AR-M700N/U (PM: 300K)

300K 600K 900K 1200K 1500K 1800K 2100K 2400K

Unit name  

No. Part name

Optical section

1

Mirror, lens, reflector, sensors

❍

❍

❍

❍

❍

❍

❍

❍

❍

2

Table glass/ Dust-proof glass/ OC

❍

❍

❍

❍

❍

❍

❍

❍

❍

3

White reference glass

❍

❍

❍

❍

❍

❍

❍

❍

❍

4

Rails

✩

✩

✩

✩

✩

✩

✩

✩

5

Drive belt, drive wire, pulley

✕

✕

✕

✕

✕

✕

✕

✕

SPF Paper feed/

Transport 
section

1

Paper feed roller

✕

✕

✕

✕

✕

✕

✕

✕

✕

(Note 1)

2

Pickup roller

✕

✕

✕

✕

✕

✕

✕

✕

✕

(Note 1)

3

Separation roller

✕

✕

✕

✕

✕

✕

✕

✕

✕

(Note 1)

4

No. 1 resist roller (Drive)

❍

❍

❍

❍

❍

❍

❍

❍

❍

5

Torque limiter

✕

✕

✕

✕

✕

✕

✕

✕

(Note 1)

6

Transport roller 1 (Drive)

❍

❍

❍

❍

❍

❍

❍

❍

❍

7

Transport roller 2 (Drive)

❍

❍

❍

❍

❍

❍

❍

❍

❍

8

Exposure section (CIS unit)

❍

❍

❍

❍

❍

❍

❍

❍

❍

Paper exit 
section

9

No. 2 resist roller (Drive)

❍

❍

❍

❍

❍

❍

❍

❍

❍

10

Paper exit roller (Drive)

❍

❍

❍

❍

❍

❍

❍

❍

❍

Drive 
section

11

Gears (Grease)

✕

✕

✕

✕

✕

✕

✕

✕

✕

UKOG-0299FCZZ

12

Belts

✕

✕

✕

✕

✕

✕

✕

✕

(Note 1)

Replacement reference: For replacement, refer to each paper feed counter value.
Paper feed tray 1 and 2

: 200K or 1 year

Manual paper feed/paper feed tray 3 and 4

: 100K or 1 year

SPF section

: 100K or 1 year

Torque limiter

: 800K (However, 400K for manual  paper feed section)

(NOTE) Paper feed section roller life

Since each roller life is 100K or 200K, if a certain paper feed unit is intensively used, its life
may be expired before the regular maintenance timing.

In actual, however, different sizes of paper are used with different paper feed trays. There-
fore, it is quite rare to have to replace one of the rollers before the maintenance timing.

When a certain size of paper is used intensively, it is advisable to set two or more paper
feed trays for that paper size as far as possible. This note should be explained to the user.

When servicing, be sure to check the use frequency of each paper feed tray, and replace
a roller if necessary.

When cleaning rollers, it is advisable to use wet waste cloth to wipe and clean.

Since the paper feed trays 3 and 4 are used for larger sizes of paper than the paper feed
trays 1 and 2, the life times of their rollers are shorter than those of the paper feed rollers
1 and 2.

The degree of wear of the paper pickup roller is greater than that of the paper feed roller,
which greater than that of the separation roller.

(Paper pickup roller > paper feed roller > separation roller)

AR-M550N/U (PM: 250K)

When 

calling 

250K 500K 750K 1000K 1250K 1500K 1750K 2000K

Remark

AR-M620N/U, AR-M700N/U (PM: 300K)

300K 600K 900K 1200K 1500K 1800K 2100K 2400K

Unit name  

No.

Part name

1

1

1

1

1

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов