Sharp AR-M550N Скачать руководство пользователя страница 303

Страница: 303 / 460

: Feb. 9 2004

AR-M550/M620/M700 SIMULATION 8 - 45

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

The paper width size detection level is displayed.

Operation/Procedure

1) Open the manual paper feed guide to the max. width.

2) Select MAX POSITION with 10-key.

3) Press [START] key.

The max. width detection level is recognized.

4) Press [CUSTOM SETTINGS] key.

5) Set the manual paper feed guide to A4R size width.

6) Select POSITION with 10-key.

7) Press [START] key.

The A4R width detection level is recognized.

8) Press [CUSTOM SETTINGS] key.

10) Select POSITION2 with 10-key.

11) Press [START] key.

12) Press [CUSTOM SETTINGS] key.

13) Open the manual paper feed guide to the min. width.

14) Select MIN POSITION with 10-key.

15) Press [START] key.

The min. width detection level is recognized.

If the above procedures are not completed normally, "ERROR" is dis-
played. If completed normally, "COMPLETE" is displayed.

30-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of sensors and detectors
in the paper feed section and the related circuits.

Section

Paper feed

Item

Operation

TANSET

Tray 1 and 2 insertion detection

TLUD1

Tray 1 upper limit sensor

TSPD1

Tray 1 remaining quantity sensor

TPED1

Tray 1 paper sensor

TLUD2

Tray 2 upper limit sensor

TSPD2

Tray 2 remaining quantity sensor

TPED2

Tray 2 paper sensor

MPLD1

Manual feed length detection 1

MPLD2

Manual feed length detection 2

MTOP1

Manual pull-out sensor 1

MTOP2

Manual pull-out sensor 2

MPED

Manual feed paper empty detection 2

MPFD1

Detection 1 of paper pass from manual paper feed

MPFD2

Detection 2 of paper pass from manual paper feed

MPRD1

Manual relay paper detection 1

MPRD2

Manual relay paper detection 2

Bypass Tray size: (The manual feed tray detection size is displayed.)

M1PFD

Tray 3 transport detection

M1LUD

Tray 3 upper limit detection

M1PED

Tray 3 paper empty detection

M1SS1

Tray 3 rear edge switch 1

M1SS2

Tray 3 rear edge switch 2

M1SS3

Tray 3 rear edge switch 3

M1SS4

Tray 3 rear edge switch 4

M1SPD

Tray 3 paper remaining quantity detection

Tray 3 size: (The tray 3 detection size is displayed.)

M2PFD

Tray 4 transport detection

M2LUD

Tray 4 upper limit detection

M2PED

Tray 4 paper empty detection

M2SS1

Tray 4 rear edge switch 1

M2SS2

Tray 4 rear edge switch 2

M2SS3

Tray 4 rear edge switch 3

M2SS4

Tray 4 rear edge switch 4

M2SPD

Tray 4 paper remaining quantity detection

Tray 4 size: (The tray 4 detection size is displayed.)

SIMULATION 30-2

TRAY SENSOR CHECK..

TANSET

TLUD1 TSPD1 TPED1 TLUD2 TSPD2 TPED2

MPLD1 MPLD2 MTOP1 MTOP2 MPED MPFD1 MPFD2

MPRD1 MPRD2

(Bypass Tray size:

)

M1PFD M1LUD M1PED M1SS M1SS2 M1SS3 M1SS4

M1SPD

(Tray3 size:

)

M2PFD M2LUD M2PED M2SS M2SS2 M2SS3 M2SS4

M2SPD

(Tray4 size:

)

40-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the manual feed tray
paper size detector and the related circuit. (The
operation of the manual feed tray paper size detector
can be monitored with the LCD display.)

Section

Paper feed

Item

Operation

MPLD1

Manual tray length detection 1

MPLD2

Manual tray length detection 2

MTOP1

Manual tray pull-out detection 1

MTOP2

Manual tray pull-out detection 2

BYPASS_WIDTH

Manual feed guide plate position

BYPASS_AD

Manual feed width detection volume output AD
value

Bypass Tray width
size

(Manual tray detection size is displayed.)
A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R, A5R,
5.5x, 7.25x, EXTRA

40-2

Purpose

Adjustment

Function
(Purpose)

Used to adjust the manual paper feed tray paper width
detector detection level.

Section

Paper feed

Item

Operation

9) Set the manual paper feed guide to A5/A5R size width.

The A5/A5R width detection level is recognized.

SIMULATION 40-1

BYPASS TRAY SENSOR CHECK..

MPLD1

MPLD2 MTOP1 MTOP2

BYPASS_WIDTH:

2100

BYPASS_AD:

600

(Bypass Tray width size:

A4/A3

)

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 303 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: