Sharp AR-M550N Скачать руководство пользователя страница 54

Страница: 54 / 460

: Feb. 9 2004

AR-M550/M620/M700 EXTERNAL VIEW AND INTERNAL STRUCTURE 5 - 23

Transport roller 1 (Drive)

Transports paper fed from the large capacity tray (LCC) to the transport
roller 2.

Transport roller 1 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 2 (Drive)

Transports paper transported from the manual paper feed and the transport
roller 1 to the transport roller 3.

Transport roller 2 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 3 (Drive)

Transports paper transported from the paper teed tray 2 and the transport
roller 2 to the transport roller 3.

Transport roller 3 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 4 (Drive)

Transports paper transported from the transport roller 3 to the transport
roller 15.

Transport roller 4 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 5 (Drive)

Transports paper fed from the paper feed tray 4 to the transport rollers 6
and 7.

Transport roller 5 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 6 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 7 (Drive)

Transports paper transported from the transport roller 5 to the transport
roller 10.

Transport roller 7 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 8 (Drive)

Transports paper transported from the paper feed tray 3 to the transport
rollers 9 and 10.

Transport roller 8 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 9 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 10 (Drive)

Transports paper transported from the transport rollers 7 and 8 to the
transport roller 11.

Transport roller 10 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 11 (Drive)

Transports paper transported from the transport roller 10 to the transport
roller 13.

Transport roller 11 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 12 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 13 (Drive)

Transports paper fed from the paper feed trays 1, 3, and 4 to toe transport
roller 15.

Transport roller 13 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 14 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 15 (Drive)

Transports paper to the transport resist roller.

Transport roller 15 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 16 (Drive)

Transports paper from the fusing roller to the paper exit roller 1.

Transport roller 16 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 17 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 18 (Idle)

Reduces friction between paper and the paper guide.

Transport roller 19 (Drive)

Transports paper transported from the paper exit roller 2 to the transport
roller 20.

Transport roller 19 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 20 (Drive)

Transports paper transported from the transport roller 19 to the transport
roller 21.

Transport roller 20 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 21 (Drive)

Transports paper transported from the transport roller 20 to the transport
roller 15.

Transport roller 21 (Idle)

Applies a pressure to paper and the transport roller to provide a transport
power of the transport roller to paper.

Transport roller 22 (Idle)

Reduces friction between paper and the paper guide.

Paper exit roller 1 (Drive)

Discharges paper to the paper exit tray. / Switches back paper.

No.

Name

Function/Operation

NOTE

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 54 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: