manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 306 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 306

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 48

4) Press [START] key.

Operation/Procedure

1) Select the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the setting (adjustment) value with 10-key.

4) Press [START] key.

Unless special measures are required, do not change the setting val-
ues below.

Operation/Procedure

2) Press [START] key.

NOTE: Set to 222.

When bit=1, correction is made.

NOTE: BIT0 is not displayed, but set to the developing bias correction

function.
This setting is forcibly made enable, and cannot be disabled.

Item

Japan

Inch 

series

AB 

series

1

INSIDE 
NORMAL

Fusing roller inside/
normal mode

185

200

205

2

OUTSIDE 
NORMAL

Fusing roller outside/
normal mode

185

200

205

3

INSIDE 
PREHEAT

Fusing roller inside/
preheat mode

140

170

170

4

OUTSIDE 
PREHEAT

Fusing roller outside/
preheat mode

140

170

170

5

LEFT 
NORMAL

Sub-heat roller/
normal mode

185

200

205

6

LEFT 
PREHEAT

Sub-heat roller/
preheat mode

140

170

170

Press [START] key.

Press [CUSTOM SETTINGS] key.

43-3

Purpose

Setting (Adjustment)

Function
(Purpose)

Fusing roller RPM setting.

Section

Fixing (Fusing)

Item

Operation

Item

Set range

Default

AR-M550N/U, 

AR-M620N/U

AR-M700N/U

1

NORMAL

0 – 99

36

35

2

SLOWDOWN

0 – 99

46

44

Press [START] key.

Press [CUSTOM SETTINGS] key.

SIMULATION 43-1

1

FUSER TEMPERATURE SET. SELECT 1-6, AND PRESS START.

1. INSIDE NORMAL 

200

   5. LEFT NORMAL 

200

2. OUTSIDE NORMAL 

200

  6. LEFT PREHEAT 

170

3. INSIDE PREHEAT 

170

4. OUTSIDE PREHEAT 

170

SIMULATION 43-1

FUSER TEMPERATURE SET. INPUT VALUE, AND PRESS START.

1. INSIDE NORMAL

200

1

1

SIMULATION 43-3

1

FUSER MOTOR SPEED SETTING. SELECT 1-2, AND PRESS 

START.

1. NORMAL   

36

2. SLOWDOWN 

46

SIMULATION 43-3

FUSER MOTOR SPEED SETTING. INPUT VALUE, AND PRESS 

START.

1. NORMAL

36

44

44-1

Purpose

Setting

Function
(Purpose)

Used to set enable/disable of correction operations in 
the image forming (process) section.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Operation

1) Each bit (7 kinds) is assigned to each correction item to set

ENABLE/DISABLE of the operation.
Each bit is assigned with 0 or 1 value. Enter the total values of
items which are desired to be valid with the 10-key. 

Item

Default

BIT1

OPC drum membrane 
decrease (sensitivity/
potential) correction

Laser power/main 
charger grid voltage

1

BIT2

The range of the toner 
patch making voltage in 
the developing bias 
voltage/main charger 
grid voltage correction is 
specified. (Voltage limit)

Developing bias/main 
grid voltage (adjusted by 
SIM 8-1 and 8-2) ±100v

1

BIT3

For humidity correction

Toner concentration 
correction

1

BIT4

Toner concentration 
correction

When the developing 
bias/main charger grid 
voltage correction is 
changed more than the 
specified level, the toner 
concentration control 
level is corrected. 

1

BIT5

Toner concentration 
correction B

Correction for the 
developer life

0

BIT6

Toner concentration 
correction C

Toner concentration 
correction in low density 
image continuous print

1

BIT7

OPC drum for 
environment correction

1

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

0

0

0

0

0

0

0

Env

Tcon_C

Tcon_B

Tcon_A

Humidity

Pcon_lm

Drum

1

SIMULATION 44-1

PROCESS CORRECTION VALUE SETTING. INPUT VALUE 0-999
AND PRESS START.
BIT1: DRUM
BIT2: PROCON_LM   BIT3: HUMIDITY
BIT4: TONERCON_A  BIT5: TONERCON_B
BIT6: TONERCON_C  BIT7: ENVIRONMENT

223

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов