Sharp AR-M550N Скачать руководство пользователя страница 427

Страница: 427 / 460

AR-M550/M620/M700 OTHER 12 - 13

B. Inserter (AR-CF2) paper jam judgment conditions

*1) The take-up position is 30mm downstream from the vertical path transport roller.

*2) The reverse stop position is 20mm downstream from the reverse sensor.

JAM CODE

Name

JAM detection method

JAM judge distance

JAM detection start trigger

JAM judge detector

REG_SEN_N

Resist sensor not-reached
JAM

Separation start

Resist sensor ON

(Distance from pick descending start to
resist sensor ON) x 5

REG_SEN_S

Resist sensor remaining
JAM

Transport start from the
take-up position (*1)

Resist sensor OFF

Max. document length (WLT) - (Resist
sensor OFF to take-up position) + 200mm

TIM_SEN_N

Timing sensor not-reached
JAM

Resist sensor ON

Timing sensor ON

Distance from resist sensor ON to timing
sensor ON + 200mm

TIM_SEN_S

Timing sensor remaining
JAM

Resist sensor OFF

Timing sensor OFF

Distance from resist sensor OFF to timing
sensor OFF + 200mm

HI_SEN_NI

Paper exit sensor not-
reached JAM (Inserter
paper feed)

Timing sensor ON

Paper exit sensor ON

Distance from timing sensor ON to paper
exit sensor ON + 200mm

HI_SEN_NP

Paper exit sensor not-
reached JAM (Main unit
paper feed)

Main unit paper exit
command receive

Paper exit sensor ON

Distance from main unit side to paper exit
sensor ON + 500mm

HI_SEN_S

Paper exit sensor remaining
JAM (Main unit paper feed)

After passing by 20mm from
the paper exit sensor ON

Paper exit sensor
OFF

Max. document length (WLT) + 200mm

Paper exit sensor remaining
JAM (Inserter paper feed)

Timing sensor OFF

Paper exit sensor
OFF

Distance from timing sensor OFF to paper
exit sensor OFF + 200mm

H_SEN_NIN

Reverse sensor not-
reached JAM (When
entering the reverse path)

Timing sensor ON

Reverse sensor ON

Distance from timing sensor ON to reverse
sensor ON + 100mm

H_SEN_NOUT

Reverse sensor not-
reached JAM (When exiting
from the reverse path)

Switchback start

Reverse sensor ON

Distance from reverse stop position (*2) to
reverse sensor ON + 100mm

H_SEN_SIN

Reverse sensor remaining
JAM (When entering the
reverse path)

Timing sensor OFF

Reverse sensor OFF

Distance from timing sensor OFF to reverse
sensor OFF + 100mm

H_SEN_SOUT

Reverse sensor remaining
JAM (When exiting from the
reverse path)

After passing 20mm from
the reverse sensor ON

Reverse sensor OFF

Max. Document length (WLT) + 100mm

FUM

POM1

POM2

TM1X

TM2X

DVM

ADM1

ADM2

VPM

TRM

SPFM

SPSM

SLUMB

K_MOT

LTM

M2S

M3S

M5S

M8S

M4S

M2P

M1P

M1LUM

T2LUM

T1LUM

M2LUM

FUM

POM1

H_MOT

K_MOT

Y_MOT

M2P

M1P

M10

M1S

M2S

M6S
M7S

M3S

M5S

M8S

M4S

POM2

TM1X

TM2X

DVM

ADM1

ADM2

VPM

LLM

LTM

TRM

SPFM

SPSM

MIM

SLUMB

Motor cross section

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 427 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: