manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 270 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 270

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 12

26

18

Used to set YES/NO of toner save 
operation. (This function is valid only 
in Japan and UK versions. (Depends 
on the destination setting of SIM26-
6.) For the other destinations, the 
same setting can be made by the 
user program P22.)

Setting

Specifications

Operation 
mode

30

Used to set the operation mode 
conforming to the CE mark (Europe 
safety standards). (Conforming to 
soft start when driving the fusing 
heater lamp.)

Setting

Specifications

Operation 
mode 
(Common)

35

Used to set whether the same 
continuous troubles are displayed as 
one trouble or the series of troubles 
with SIM 22-4 when the same 
troubles occur continuously.

Setting

Specifications

38

Used to set CONTINUE/STOP of 
printing when maintenance timing is 
over and the count value reaches 
110% of replacement timing (life). 

Setting

Other

Specifications

41

Used to set YES/NO of the 
automatic magnification ratio 
selection (AMS) in the pamphlet 
mode.

Setting

Specifications

Operation 
mode 
(Common)

50

Black-White reverse YES/NO setting

Setting

Specifications

Operation

52

Used to set whether non-print paper 
(insertion paper, cover paper) (blank 
image print paper) is counted up or 
not.

Setting

Paper transport 
(Discharge/
Switchback/
Transport)

Specifications

Operation 
mode

68

Used to set ENABLE/DISABLE of 
the CA key cancel function of print 
stop.

Setting

Specifications

Operation

27

1

Used to set the specifications for 
operations in case of communication 
trouble between the host computer 
and MODEM (machine side). (When 
communication trouble occurs 
between the host computer MODEM 
and the machine, the self diag 
display (U7-00) is printed and setting 
for inhibition of print or not is made.)

Setting

Communication 
unit (TEL/LIU/
MODEM etc.)

Specifications

Operation 
mode

5

Used to enter the machine tag No. 
(This function allows to check the tag 
No. of the machine with the host 
computer.)

Setting

Communication 
unit (TEL/LIU/
MODEM etc.)

Specifications

Operation 
mode

30

1

Used to check the operation of 
sensors and detectors in other than 
the paper feed section and the 
operations of the related circuits.

Operation test/Check

Operation

2

Used to check the operation of 
sensors and detectors in the paper 
feed section and the related circuits.

Operation test/Check

Paper feed

Operation

40

1

Used to check the operation of the 
manual feed tray paper size detector 
and the related circuit. (The 
operation of the manual feed tray 
paper size detector can be 
monitored with the LCD display.)

Operation test/Check

Paper feed

Operation

2

Used to adjust the manual paper 
feed tray paper width detector 
detection level.

Adjustment

Paper feed

Operation

7

Used to enter the manual paper feed 
tray paper width adjustment value.

Adjustment/Setup

Paper feed

Operation

Code

Function (Purpose)

Purpose

Section

Item

Main

Sub

1

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов