manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 274 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 274

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 16

53

6

Used to adjust the DSPF width 
detection level.

Adjustment

Operation

7

Used to enter the SPF width 
detection adjustment value.

Adjustment/Setup/
Operation data output/
Check (Display/Print)

DSPF

Operation

8

Used to adjust the document scan 
start position. (Used to adjust the 
scanner scan position in the SPF 
mode front scan.)

Adjustment

55

1

Used to set the specifications of the 
engine control operations. (PCU 
PWB)

Setting

Operation

Specifications

2

Used to set the specifications of the 
scanner control operations. 
(Scanner control PWB)

Setting

Operation

Specifications

3

Used to set the specifications of the 
controller operations. (MFP control 
PWB)

Setting

Operation

Specifications

56

1

Used to transfer the MFP controller 
data. (Used to repair the PWB.)

Data transfer

MFP controller

Data transfer

60

1

Used to check the MFP control 
(DRAM) operations (read/write).

Operation test/Check

ICU

Operation

61

1

Used to check the operation of the 
scanner (write) unit (LSU).

Operation test/Check

Scanner (write) 
unit (LSU)

Operation

2

Used to adjust the laser power 
(absolute value) in the copy mode. 

Adjustment

Scanner (write) 
unit (LSU)

Operation

3

Used to adjust the laser power 
(absolute value) in the FAX mode.

Adjustment

Scanner (write) 
unit (LSU)

Operation

4

Used to adjust the laser power 
(absolute value) in the printer mode. 

Adjustment

Scanner (write) 
unit (LSU)

Operation

62

1

Used to format the hard disk.

Data clear

MFP controller 
(HDD)

Clear

2

Used to check the operation of the 
hard disk (read/write). (Only in the 
model with a disk installed) (Partial 
check)

Operation test/Check

MFP controller 
(HDD)

Operation

3

Used to check the operation of the 
hard disk (read/write). (All areas 
check)

Operation test/Check

MFP controller 
(HDD)

Operation

6

Used to check the operations of the 
hard disk. (The self diag operation of 
the SMART function is executed.)

Operation test/Check

MFP controller 
(HDD)

Clear

7

Used to check the operations of the 
hard disk. (The result of the self diag 
operation of the SMART function is 
printed out.)

Operation test/Check

MFP controller 
(HDD)

Clear

8

Used to format the hard disk (the 
system area excluded).

Data clear

MFP controller 
(HDD) 

Clear

10

Used to delete a job complete list 
(also to delete job log data)

Data clear

MFP controller 
(HDD) 

Clear

11

Used to delete document filing data. 
(The management area (standard 
folder, user folder) is cleared.)

Data clear

MFP controller 
(HDD) 

Clear

63

1

Used to check the result of shading 
correction. (The shading correction 
data are displayed.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Optical (Image 
scanning)

Operation

2

Used to execute shading.

Adjustment

Optical (Image 
scanning)

Operation

7

Used to adjust the white plate scan 
start position for shading. (Document 
table mode)

Adjustment

Laser (Exposure)

Operation

Code

Function (Purpose)

Purpose

Section

Item

Main

Sub

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов