Sharp AR-M550N Скачать руководство пользователя страница 287

Страница: 287 / 460

: Feb. 9 2004

AR-M550/M620/M700 SIMULATION 8 - 29

Operation/Procedure

1) Enter the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is stored, and the voltage corresponding to the set
value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

(The transfer output voltage adjustment and output check can be made
in the transfer belt cleaning mode.)

Operation/Procedure

1) Select the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key.

(The set value is saved in the memory and the voltage correspond-
ing to the set value is outputted for 30sec.)

Press [CUSTOM SETTINGS] key to stop the operation.

Operation/Procedure (Not used)

1) Select the number corresponding to the adjustment item with 10-

key.

2) Press [START] key.

(The voltage is outputted for 30sec.)

When [CUSTOM SETTINGS] key is pressed, the operation can be
stopped.

The output voltage can be adjusted with the adjustment volumes
VR101/VR102 on the high voltage PWB (fusing bias).

8-17

Purpose

Operation test/Check

Function
(Purpose)

Used to check and adjust the operation of the transfer
voltage and the related circuit. (Transfer belt cleaning
mode)

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Operation

Item

Set range

Default

SHF FRONT

AC component

0 - 450

450

SHV BACK

AC component

0 - 450

450

THV-

DC component

0 - 150

Press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

8-18

Purpose

Adjustment/Operation test/Check

Function
(Purpose)

Used to check and adjust the voltage of the transfer CL
roller cleaning/transfer CL roller print mode and the
control circuit.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

SIMULATION 8-17

TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START.

1.SHV FRONT

450

2.SHV BACK

450

3.THV-

SIMULATION 8-17

TRANSFER ROLLER SETTING. INPUT VALUE, AND PRESS START.

1.FRONT (0-600)

450

SIMULATION 8-17

TRANSFER ROLLER SETTING. EXECUTING···.

1.FRONT(0-600)

450

(The output voltage of the transfer CL roller cleaning/transfer CL roller
print mode can be adjusted and checked.)

Item

Set range

Default

Transfer CL roller (Print)

CRHV PLUS

0 - 250

200

Transfer CL roller (Cleaning)

CRHV MINUS

0 - 250

200

Press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

8-19

Purpose

Adjustment/Operation test/Check

Function
(Purpose)

Used to check and adjust the fusing bias voltage and
the control circuit. (Not used)

Section

Fusing

Item

Adjustment VR

Fusing bias (-)

FBIAS

VR 101

Fusing bias (+)

VR 102

Press [START] key.

Press [CUSTOM SETTINGS] key.
Or after 30sec output.

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. SELECT 1-2, AND

PRESS START.

1.CRHV PLUS

200

2.CRHV MINUS

200

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. INPUT VALUE, AND

PRESS START.

1.CRHV PLUS (0-250)

200

SIMULATION 8-18

TRANSFER CLEANING ROLLER SETTING. EXECUTING···.

1.CRHV PLUS(0-250)

200

SIMULATION 8-19

FUSING BIAS CHECK. SELECT 1, AND PRESS START.

1.FBIAS

SIMULATION 8-19

FUSING BIAS CHECK.. EXECUTING···

1.FBIAS

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 287 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: