manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 327 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 327

AR-M550/M620/M700  SIMULATION  8 - 69

(Table 2)

(Table 3)

Operation/Procedure

(Lead edge image loss adjustment) (Table 1)

1) Set the front and back surface image loss adjustment values

(LEAD EDGE) as specified below:

(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge: 3.5mm (DENA: 35)

∗

Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)

2) Make a duplex copy at 100% with the SPF, and check that the lead

edge (image loss) is 1.5mm either on the front surface and the
back surface. (Select the duplex mode in the paper selection mode
of SIM 50-6.) (Table 3) (Enter 100 as the copy magnification ratio
set value (MAGNIFICATION), and press [START] key.)

If the adjustment result is not satisfactory, perform the following proce-
dures:

3) Change the adjustment values of SIDE1 and SIDE2, and perform

the adjustment. (Change the adjustment values of SIDE1 and
SIDE2, and press [START] key.)

(Shift for the adjustment value change: 0.1mm/step)

(The image scan start timing is determined with the detection tim-
ing of the document lead edge by the detector SPPD4.)

Repeat procedures 2) and 3) until a satisfactory result is obtained. 

(Rear edge image loss adjustment)

1) Use the SPF at 100% to make a duplex copy, and check that the

rear edge image loss is 1.5mm on the front and the back surfaces.
(Select the duplex mode in the paper selection mode of SIM 50-6.)
(Enter 100 as the copy magnification ratio set value (MAGNIFICA-
TION), and press [START] key.)

If the adjustment value is not satisfactory, , perform the following pro-
cedure. 

2) Change the adjustment value of TRAIL EDGE. Change the adjust-

ment value of TRAIL EDGE, and press [START] key. 

Repeat the above procedures until a satisfactory result is obtained. 

(Front/rear frame direction image loss adjustment)

Set the adjustment value of the front surface and the back surface
(FRONT/REAR) to 20. (Enter 20 as the adjustment value of FRONT/
REAR, and press [P] key.)

When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.

NOTE: When [P] key is pressed after entering the adjustment value,

the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.
(Table 2)

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key. 

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. (Table 3)

4) Press [START] key. (The paper feed tray is selected.)

∗

To set the copy magnification ratio, perform the following procedure.

(Void set value)

17 LEAD_EDGE

(DENA) 

Lead edge void set 
value

0 - 99

35

18 TRAIL_EDGE

(DENB)

Rear edge void 
adjustment value

19 FRONT/

REAR

Front/Rear void 
adjustment value

20 SIDE2 ADJ.

RRCB correction 
value in the back 
surface print mode

1 - 99

50

Normal display

NOW PRINTING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

Side LCC

Select 0, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

Item

Set 

range

Default

AR-M550N/U, 

AR-620N/U

AR-

M700N/U

50

2

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key, 
or terminate copying.

SIMULATION 50-5

LEAD EDGE ADJUSTMENT. NOW PRINTING.

SIMULATION 50-5

LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

2.RRCB

Select 1, 
and press 
[START] key.

Select other than 0 - 1, and press [START] key.

SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT 

1

  1.PRINT START

(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB 

50

   20.SIDE2 ADJ. 

50

RESIST:  3.T1 

50

   4.T2 

50

   5.T3 

50

  6.T4 

50

         7.BPT 

50

  8.LCC 

50

  9.ADU 

50

OFF CENTER: 10.T1 

50

  11.T2 

50

  12.T3 

50

  13.T4 

50

            14.BPT 

50

  15.LCC 

50

  16.ADU 

50

(VOID SETTING) 17.LEAD_EDGE(DENA) 

50

               18.TRAIL_EDGE(DENB) 

30

  19.FRONT/REAR 

30

1

SIMULATION 50-5

LEAD EDGE ADJUSTMENT. SELECT 1-16, AND PRESS START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

  (ABOVE+10: DUPLEX MODE)

50-6

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy image position and void area 
(image loss) on print paper in the copy mode. (The 
similar adjustment can be performed with SIM 50-7 
(simple method).) (SPF mode)

Section

Item

Picture quality

SIDE1:  SPF front surface document lead edge scan position

adjustment value

SIDE2:  SPF back surface document lead edge scan position

adjustment value

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов