manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 242 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 242

AR-M550/M620/M700  SETTING AND ADJUSTMENTS  7 - 27

This adjustment is needed in the following situations: 

• The MFP control PWB has been replaced.

• The EEPROM on the MFP control PWB has been replaced.

• The scan control PWB has been replaced.

• The EEPROM on the scan control PWB has been replaced.

• The scanner (reading) section has been disassembled. 

• The scanner (reading) unit has been replaced. 

• U2 trouble has occurred. 

• The SPF section has been disassembled. 

• The SPF unit has been replaced. 

This adjustment is intended to adjust the scanner read position in SPF-
mode front face scan. 

An incorrect adjustment would deviate the scanner stop position from
the required position, thus possibly causing a shadow of the original
table to appear at the leading edge of an image generated by SPF
(front-face) mode scan. 

1) Make a copy in SPF (front-face) mode, and make sure that the

printed image at the leading edge of the copied image is free from
shadows.

If the printed image at the leading edge of the copied image contains a
shadow of the original table, then do the following steps. 

2) Go through the modes specified in Simulation 53-8.

3) Enter the adjustment value and press the Start key. 

Repeat the above adjustments until an acceptable result is obtained.

This adjustment is needed in the following situations: 

• The MFP control PWB has been replaced.

• The EEPROM on the MFP control PWB has been replaced.

• The scan control PWB has been replaced.

• The EEPROM on the scan control PWB has been replaced.

• The scanner (reading) section has been disassembled. 

• The scanner (reading) unit has been replaced. 

• U2 trouble has occurred. 

• The SPF section has been disassembled. 

• The SPF unit has been replaced.

ADJ 8B

Adjust the original scan start position 
(adjust the scanner read position in 
SPF-mode front face scan)

Select 2, and 
press [START] key. 

Press [START] key, or 
press [CUSTOM SETTINGS] key.

Image area

Papar lead edge

Shadow image of SPF

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. PRESS START.

2.MANUAL   

25

25

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. INPUT VALUE 1-70, AND

PRESS START.

2.MANUAL

ADJ 8C

Adjust the copied image loss/void area 
in SPF mode

Image loss (LIL)

LIL  = 1.5 mm
LV 

= 3.5 mm

TV  = 3.5 mm

FV+RV = 7.0 mm

Papar lead edge

Papar tail edge

10

20

No Image

No Image

No Image

No Image

Void (TV)

Void (LV)

Void (FV)

Void (RV)

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов