Sharp AR-M550N Скачать руководство пользователя страница 328

Страница: 328 / 460

AR-M550/M620/M700 SIMULATION 8 - 70

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

(Table 1)

(Table 2)

(Table 3)

When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.

Operation/Procedure

(Lead edge image loss adjustment)

1) Set the front and back surface image loss adjustment values

(LEAD EDGE) as specified below:

(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge void: 3.5mm (DENA: 35)

∗

Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)

2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment

value of L4, and press [P] key.

3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment

value of L5, and press [P] key.

4) Make a copy at 200% with the SPF, and calculate the values of L4

and L5. (Enter 200 as the set value of the copy magnification ratio
set value (MAGNIFICATION) and press [START] key.)

Set range

25 - 200 (%)

Item

Set

range

Default

TRAY SELECT

Paper feed tray selection

1 - 6

–

COPY START

Copy START (Default)

–

MAGNIFICATION Print magnification ratio

25 -

200%

–

(Lead edge adjustment value)

SIDE1

Front surface document
scan start position
adjustment value

0 - 99

SIDE2

Back surface document
scan start position
adjustment value

(Image loss set value: SIDE 1)

LEAD_EDGE

Front surface lead edge
image loss set value

0 - 99

FRONT_REAR

Front surface side edge
image loss set value

TRAIL_EDGE

Front surface rear edge
image loss set value

0 - 20

(Image loss set value: SIDE 2)

LEAD_EDGE

Back surface lead edge
image loss set value

0 - 99

FRONT/REAR

Back surface side edge
image loss set value

10 TRAIL_EDGE

Back surface rear edge
image loss set value

0 - 20

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

TRAY1

TRAY2

TRAY3

TRAY4

BPT

Manual feed

LCC

Side LCC

Select 2, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

50-7

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy image position and void area
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-6.)
(SPF mode)

Section

Item

Picture quality

L4 = Distance (mm) from the image lead edge position to the

scale of 10mm x 10

SIMULATION 50-6

LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS

START.

0.TRAY SELECT

1.COPY START

2.MAGNIFICATION

100

(ADJUSTMENT DATA)3.SIDE1

4.SIDE2

(IMAGE LOSS SETTING)

SIDE1: 5.LEAD_EDGE

6.FRONT/REAR

7.TRAIL_EDGE

SIDE2: 8.LEAD_EDGE

9.FRONT/REAR

10.TRAIL_EDGE

Press [CUSTOM SETTING] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

Press [START] key or
press [CUSTOM SETTINGS] key.

SIMULATION 50-6

LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS

START.

3.SIDE1

SIMULATION 50-6

LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.

SIMULATION 50-6

LEAD EDGE ADJUSTMENT(SPF). SELECT 1-16, AND PRESS

START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

(ABOVE+10: DUPLEX MODE)

Select 1,
and press
[START] key.

Select 0, and press [START] key.

Select other than 0 - 2, and press [START] key.

100

SIMULATION 50-6

LEAD EDGE ADJUSTMENT(SPF).

(MAGNIFICATION)

INPUT 25-200(%)

Содержание AR-M550N













































































































































































































































































































































































































































































Результаты поиска

Содержание AR-M550N

Отзывы:

Sharp AR-M550N, Руководство по обслуживанию, Страница: 328 / 460

Результаты поиска

Содержание AR-M550N

Отзывы: