manualshive.com logo in svg

Sharp AR-M550N, Руководство по обслуживанию, Страница: 325 / 460

Поделиться
Скачать
Sharp AR-M550N Скачать руководство пользователя страница 325

AR-M550/M620/M700  SIMULATION  8 - 67

Operation/Procedure

(Lead edge image loss/void area adjustment)

1) Set the RRGB value of SIM 50-1 to 80 - 99.

2) Set the lead edge image loss adjustment value (LEAD EDG) and

the paper lead edge void adjustment value (DENA) to the values
specified below.

(Standard set value) Lead edge image loss: 1.5mm
Paper lead edge void: 3.5mm (DENA: 35)

∗

Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD and press [P] key.

∗

Set the adjustment value of DENA to 35. (Enter 35 as the adjust-
ment value of DENA and press [P] key.)

3) Set the adjustment value of L1 to 0. (Enter 0 as the adjustment

value of L1, and press [P] key.)

4) Set the adjustment value of L2 to 0. (Enter 0 as the adjustment

value of L2, and press [P] key.)

5) Make a copy at 400%, and calculate the values of L1 and L2.

(Enter 100 as the set value (MAGNIFICATION) of the copy magni-
fication ratio, and press [START] key.) (Place a scale on the docu-
ment table and make a copy.)

6) Enter the above values as the set values of L1 and L2. (Enter the

adjustment values of L1 and L2, and press [P] key.)

If the adjustment result is not satisfactory, perform the above proce-
dures again from the beginning, or use SIM 50-1 to adjust.

NOTE: If a satisfactory result is not obtained with the above proce-

dures, through the adjustment values are changed individually,
the normal adjustment cannot be made. 

Perform procedures 3) to 6) continuously.

(Rear edge void area adjustment)

Adjust so that the rear edge void area is 3.5mm. (Change the adjust-
ment value of TRAIL EDGE, and press [START] key.)

(Front/rear frame direction image loss adjustment)

Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment
value of SIDE, and press [P] key.)

When this adjustment value is changed, the image position is shifted in
the front/rear frame direction.

(Front/rear frame direction void area adjustment)

Adjust so that the total of the front/rear direction void areas is 7.0mm.
(Change the adjustment values of FRONT/REAR, and press [START]
key.)

Front frame void area = 3.5mm

Rear frame void area = 3.5mm

If, as shown above, the front and the rear void areas are not even, use
SIM 50-5 to adjust the image off-center position.

NOTE: When [P] is pressed after entering an adjustment value, the

adjustment value is set. When [START] key is pressed instead,
the adjustment value is set and copying is performed.)

(Copy condition in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key.

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray of the tar-

get paper with 10-key.

4) Press [START] key. (The paper feed tray is selected.)

∗

To set the magnification ratio, perform the following procedure.

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

50-2

Purpose

Adjustment

Function
(Purpose)

Used to adjust the document scan position, the image 
print position, and the void area (image loss). (Simple 
adjustment) (This adjustment is the simple method of 
SIM 50-1.) (Document table mode)

Section

Item

Picture quality

Image position

L1 = Distance (mm) from the image lead edge position to the

scale position of 10mm x 10

L2 = Distance (mm) from the image lead edge position to the

paper lead edge x 10

Item

Content

Set 

range

Default

0

TRAY SELECT

Paper feed tray selection

1 - 6

–

1

COPY START

Copy START (Default)

–

–

2

MAGNIFICATION

Print magnification ratio

25 - 

400%

400

(Lead edge adjustment value)

3

L1

Distance from the image 
lead edge to the scale of 
10mm. (Platen 400%, 
0.1mm increment)

0 - 999

–

4

L2

Distance from the paper 
lead edge to the image 
lead edge (0.1mm 
increment)

–

(Image loss set value)

5

LEAD

Lead edge image loss 
set value

0 - 99

15

6

SIDE

Side image loss set value

20

(Void set value)
7

LEAD_EDGE 
(DENA)

Lead edge void set value

0 - 99

35

8

TRAIL_EDGE 
(DENB)

Rear edge void 
adjustment value

9

FRONT/REAR

Front/Rear void 
adjustment value

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

Side LCC

Set range

25 - 400 (%)

Содержание AR-M550N













































































































































































































































































































































































































































































Отзывы:

Нет отзывов